Search results

  1. dlogvine

    Gel coat hardening in cold weather

    I wonder if I can get gelcoat to harden in 60F. Otherwise will have to wait till it gets warmer
  2. dlogvine

    Is this a 5.7 v8 or 4.3 v6 vortec flywheel?

    The description of the flywheel says MerCruiser GM 4.3l LX Vortec Flywheel 14103283 N 168 Teeth However it has also 5.7 mercruiser in the detailed description. Are these flywheels the same?
  3. dlogvine

    Connector for thunderbolt iv amplifier

    I am trying to adjust the engine wire harness from 1995 mercruiser v8 5.7 to 2000 Mercruiser 4.3 Vortec. Looks like it is very similar, but I cannot get a connector for the thunderbolt IV amplifier, which is located on the distributor. Buying a whole new thunderbolt iv or v ignition module is...
  4. dlogvine

    Wire harness for 2000 mercruiser 4.3 Vortec carb engine

    1. Can the wire harness for 1995-1997 (could be earlier, since the engine had a mechanical fuel pump) Mercruiser 5.7 be rewired for the 2000 Mercruiser 4.3 Vortec Engine. I looked at the wiring diagrams and they are pretty similar. One difference was the fuel pump wire and the other was a...
  5. dlogvine

    Led bar shines in a wrong place

    I installed a couple led bars on my wakeboard tower hoping it would help driving the boat at night. Instead the light lifts the bow and deflected light blinds the driver. I'm thinking about putting some kind of deflector on the bottom of the light to point the Ray only forward and bot down...
  6. dlogvine

    Gelcoat application

    Today I tried to spray gelcoat first time (in my life). So first of all I made sure my cleaning liquid was at hand and ready for use. Next I made sure I can measure resin hardener ratio correctly. Felt like counting drops was a really crappy idea, I decided to do it mathematically correct using...
  7. dlogvine

    Gelcoat thinner

    I am planning on gelcoating my restored 2006 Baja islander. I started with filling surface dents and damaged fiberglass surfaces with fiberglass patch. Sanded and polished the fiberglass. Now I want to spay the repaired areas with the gel coat. I have a 27 gal compressor and a cheap hvlp spray...
  8. dlogvine

    Storage compartment for 2006 Baja Islander 202

    I purchased the hull of 2006 Baja Islander 202 and installed the drivetrain - Mercruiser v8 5.0 with an Alpha 1 gen 2 outdrive. Replaced all the upholstery except the captains seats (might do it later). Next will be gelcoat painting it. The boat is well designed and I like the accessibility of...
  9. dlogvine

    Gear lube monitor wiring

    I dropped a new, or better said newly rebuilt 1993 v8 305 Mercruiser, into a 2006 Baja Islander 202 boat. Just got it running last night. The old engine did not have a gear lube monitor, but a newer outdrive and the gimbal housing have a setup for the gear lube monitor, which I installed. Now I...
  10. dlogvine

    4.3 Mercruiser vs. 4.3 Volvo penta mounts

    I bought a hull of a 2004 Larson 180 sei. It had originally a 4.3 Volvo penta engine, but I'm putting in a 4.3 mercruiser. There is still original wire harness from the dash to the engine, and it has an original shifter. I have a couple questions, 1. Do the mount holes for Volvo penta engine...
  11. dlogvine

    Alpha one gen 2 Gimbal housing gasket seal

    I'm replacing a Volvo penta 4.3 v6 original engine with Mercruiser 4.3. The outdrive and gimbal housing is replaced with the alpha one gen 2 version. I had to drill 2 holes in a transom to fit the alpha 1 gen 2 gimbal housing and decided to replace the rubber gasket/seal in the gimbal. The new...
  12. dlogvine

    Hole pattern for Alpha one gen 2 outdrive

    Originally 2004 Larson 185 hull I purchased had a Volvo penta 4.3 engine with SX outdrive. But i had an older 4.3 mercruiser engine with Alpha one gen 1 outdrive and transom plate and bell housing. The bolt pattern on gen 1 outdrive matched the original 6 hole pattern. But I decided to put a new...
  13. dlogvine

    Wrong outdrive gear ratio

    My friend is using a wrong gear ratio outdrive on his boat. He has 1.83 gear ratio which is for 4.3l v6 engine but his engine is 3.0l. I told him it is not a good combination. But I want to know for myself How damaging is this setup for the engine and the outdrive. Thank you
  14. dlogvine

    Broken bolts in the bellows housing

    I'm replacing the bellows housing and transom plate for Alpha One Gen 2 outdrive. When I removed the v-pipe I saw that two bolts on the bottom were broken. When removing the trim sender, another bolt broke. Two of the V-pipe fastener bolts im planning on removing by welding a couple nuts on the...
  15. dlogvine

    Toyota tacoma rear differential breather kit and water in the gear oil

    I know it might be the wrong forum but it is related to the boating and water so I will post the question here, if not, I'll try to find some toyota trucking forum and ask it there. After taking my boat to the lake I noticed some oily drops under my rear differential of my 2015 Toyota Tacoma trd...
  16. dlogvine

    Mercruiser trim sender and trim limit kit, generic vs. brand name

    Im going to replace the trim sender and trim limit units and I found several generic brand kits on ebay. They run about $28-35. Sierra of Mercury similar kits run for almost 3 times more, around $75. Is there any significant difference in quality between these units and can I buy the cheaper...
  17. dlogvine

    is it possible to treat old fuel in the tank

    The most recent tags on the 2008 Baja Islander I purchased are from 2016. The tank contained about 1/4 fuel. I added Enzime treatment and Stabil for fuel and filled the rest with the 91 high octane fuel. The engine is newly rebuilt and installed 1993 Mercruiser V8 305. Old fuel did not have this...
  18. dlogvine

    outdrive stand plan

    Can anybody direct me to the thread with outboard stand plans, I know it is somewhere here but cant find it for my lives sake. Thank you
  19. dlogvine

    Cables for dual shifter throttle and old shifter plate

    I bought a 2008 Baja hull without the engine and outdrive. The engine and outdrive I was going to use were newly rebuild 1993 5.0 v8 engine with the rebuilt outdrive. The wiring is matching, I just had to add an extra wire for the gear lube control bottle. But when i tried to attach the shifter...
  20. dlogvine

    New engine in the boat, how can i reset the engine hours on the speedometer?

    I just installed a brand new (or newly rebuild) engine and outdrive on the Baja boat hull I recently bought. The hour meter build in the speedometer shows a lot of hours (I think over 2300 hours). Is there any way to reset this hour meter to reflect hours for the new engine? It looks like it is...
Top