Search results

  1. pcmpete

    Block off plate for VP 280

    does anyone know if there is an exhaust block off plate suitable for the Volvo 280 outdrive. I found the volvo 872238 but not sure if it fits.
  2. pcmpete

    Pro & Cons of using an Air Box

    What are the pros and cons of using an air box on your engine? With a flame arrester in it, it should be ok for marine use. I am thinking about for more of a 'bling thing' but do not want to hurt the performance either. With the ducting facing forward should help in getting nice flow of clean...
  3. pcmpete

    Holley 80312 carb question

    I used picked up a holley 80312 carb for my ford 302. There is no fuel inlet fitting, does anyone know what fitting would fit this and/or any metal lines available that would suit this carb to the pump? Thanks
  4. pcmpete

    AQ130c - Solex problem

    What would cause large amounts of fuel to shoot out both solex carbs at the same time? I was doing some engine running yesterday, checking the temp and idle, got the motor running ok. Today I went to work on it again. Because I live in Arizona and the boat is in my garage i didn't pump the...
  5. pcmpete

    Craftman Engine Analyzer manual?

    Hi, I tried posting this in FAQ's section first, but couldn't. I picked a Craftsman Engine Analyzer (161.210400) with cable at a local swap-meet, but there was no manual/instructions for it. Would anyone on iboats have a copy of this manual in print form or PDF? Thanks. Moderator feel free to...
  6. pcmpete

    AQ130c - normal running temp and issues

    My temp seems to be running higher than normal, after warm up and 5-10 wot run the temp goes up to 220-230 then back at idle it slowly drops to 200. I did have a slight overheat issue the last time I took the boat out when the copper pipe from the water pump to the oil cooler came off at the...
  7. pcmpete

    Wet Exhaust temp?

    What is the temps can wet exhaust manifolds/riser reach? I am asking to see if I can use engine paint that can handle upto 500 degrees F. Thanks
  8. pcmpete

    Exhaust Manifold Bolt Grades?

    After removing my manifolds to clean them up and repaint them. The bolts that held on the manifold look a bit rusty and I am not 100% comfortable in using this bolts. i went to my local hardware store and they had the following bolts: 1. Grade 5 Stainless Steel 2. Grade 8 non-stainless steel...
  9. pcmpete

    upper Shift Shaft movement

    I am currently rebuilding a MC-1 outdrive/bellhousing assembly. On the bellhousing I noticed that there is a slight up and down movement on the upper shift shaft (#22)...
  10. pcmpete

    Merc 470 Prop Choice/Query

    Hi there, I am looking for a prop for my setup, boat came with no prop, so I need your help. My info: Iboats Boat and Motor Info 1. Year, make and model of boat 1978, Reinell T180 (Nada: http://www.nadaguides.com/default.as...R&d=1600148440) 2. Length, width and base weight of boat, look for...
  11. pcmpete

    Reinell T1801 Complete Restore

    Reinell T1801 restoration Table of Contents: # Task Description 1. Remove wood / fiberglass & foam COMPLETE 2. Grind hull COMPLETE 3. Build new Transom & Install COMPLETE 4. Build new Engine Stringers & Install...
  12. pcmpete

    Very unique AQ151c

    Just found this on youtube, very nice looking setup: http://www.youtube.com/watch?v=vsZW56WcqvY
  13. pcmpete

    Oil Pressure Sender on Aq130

    My Aq130 has the standard oil pressure switch fitted, but I want to fit an oil pressure sender that will work with a gauge. But the sender does not fit because of the copper cooling pipe going into the oil cooler. Are there adapters available will mount the sender at an angle to clear the pipe...
  14. pcmpete

    MC-1 interchange with Alpha 1

    My gimbal ring has developed alot of slop, so it or the steering shaft needs replaced. Question: Can I use an Alpha 1 Bellhousing/Gimbal Ring assembly with the MC-1 transom plate and MC-1 outdrive? Thanks
  15. pcmpete

    Volvo 270 Suspension fork movement (with video)

    I am in the process of trying to remove 'most' of the steering slop from the drive. During this process I noticed that the Suspension fork can move approx 1/16" side to side on the transom shield pins producing some slop. Is this normal? If not I take it that the bushings need replaced or can a...
  16. pcmpete

    Volvo 270 lumpy steering

    my steering on my vp270 feels lumpy at slow speeds, let me explain: 'sometimes' the steering would feel stiff at no wake speed then it suddenly goes free and turns easy, it is almost like something is holding and then lets go. It does this in both directions. It is not power assisted but it...
  17. pcmpete

    aq130 copper pipe and close call

    I took my Aq130c powered boat out at the weekend, everything was going good. Then the temp started to rise to 280 and water was coming from the dog house. I quickly realized that a cooling pipe/tube had come off, so I had to think quick, do I shut it down and run the risk of it not starting...
  18. pcmpete

    Cam selection

    I am putting a 302 motor into a 16ft boat, would a camshaft for higher rpm work or would a cam for torque still be required. The power to weight ratio should be good so the hole shot should not be a problem, just looking for higher top speed. Please advise....
  19. pcmpete

    Brake service/checking

    Just got a trailer with surge brakes. The boat is not ready to be put on the trailer yet, so I want to service the trailer while I have full access to it. What is the procedure for servicing and/or checking the braking system. Would this be possible without the load of the boat on the trailer...
  20. pcmpete

    Merc 470 - 16ft Boat Prop Choice/Query

    New boat to me, came with no prop so I have no baseline to work with. But need to know what prop to get/try first. Details: Reinell T180 Length 16'8" Beam 87" Dry Weight 2028 pound Motor/Outdrive Mercruiser 470 (170hp) with MC1 with ratio 1.84 Tank size 18gals Normal loading will be two adults...
Top