Search results

  1. npd4432

    Got her running today.

    I recently had a 7 HP chrysler tiller model 72HA given to me. I finally had some time to work on it and after all the cleaning and replacing of some parts, she fired up in about 10 pulls. I let it run for about 2 minutes on the muffs and it seemed to be getting pretty hot. There was some...
  2. npd4432

    Parts question

    I have done some searching on the net and cannot find an impeller for my 7 hp chrysler tiller motor. Model # 72HA. Is this still available? If so where can I get it.
  3. npd4432

    7 HP Chrysler tiller

    I just had a 7 HP chrysler tiller motor given to me which has been sitting for a few years. I am going to try to wake this piece up and need to know some basics. The model # is 72HA. What year is this motor? What type of plugs and the plug gap should I use? Is the premix 50:1? Thanks in...
  4. npd4432

    fuel pump rebuild on 75 HP rude

    I bought a fuel pump rebuild kit and installed it on my motor today. It took me about 5 times of putting it back together to not have any of the gaskets and membrane leak. So here is my question, how do I know if the old parts were bad? The center membrane looked ok but was disformed and...
  5. npd4432

    Fuel Pump Rebuild for '83 75 HP

    I may need to replace/rebuild the fuel pump on my motor, I see the rebuild kits listed for about $20.00. I look at the pictured parts and it does not seem too complicated to rebuild but I always ask before tearing somthing apart, what am I getting into??
  6. npd4432

    Nauticus Smart Tabs

    I bought the smart tabs for my boat last year and they are working excellent. I just wanted to say a few things about the company itself. I have never had a better experience in customer service as I have with them. Originally when installing I had a few questions as to location, questions...
  7. npd4432

    75 HP Evinrude "breaking up" at WOT

    When operating usually at WOT between 5500 and 5800 RPM the motor seems to cut out for short periods (for about a second) and then continues as normal. This seems to me to be an electrical ignition or spark problem. My question is where do I start to try to diagnose the problem? Plugs, wires...
  8. npd4432

    Evinrude 48 SPL

    I am considering buying a pontoon boat with an Evinrude 48 SPL 2 cyl. motor. I am just wondering what is the difference between this and a 50 HP motor? Has anybody had any bad luck with these? Just trying to do some research before purchase.
  9. npd4432

    Plug gap for Kawasaki 750

    Does anybody know the proper plug gap for the BR8ES for a 1995 750 ZXI?
  10. npd4432

    1983 75 HP bogging on hole shot

    I dont know what can be going on but here it goes, multiple people have been using my boat this season and yesterday when I took it out I was going to water ski and when hitting it on hole shot it would stall. I had to feather the throttle to get to WOT. I went over most of the suspected items...
  11. npd4432

    1995 Kawasaki jet ski switch problems

    Just picked up a 1995 Kawasaki Jetski 750. The orange on/off ignition switch seems to be on the blink. It will not turn off the ski, will crank and not start in the on or off position. It seems I need a new switch, but my question is there are four wires going to the switch a black, white red...
  12. npd4432

    Anode fell off

    While servicing my motor before I put my boat in the water for the year I had taken the anode off to clean it, It felt to me like it was plastic and acted like plastic when put against some sandpaper. Well anyway after some crusing around I tilted the motor up and it was gone. Will this effect...
  13. npd4432

    Installation of new boyesen reeds on 75 HP Evinrude

    Just got my new Boyesen Reeds in the mail yesterday along with the gasket for the carbs. Any tips or tricks on how to install? Also, the instructions speak of re-jetting the low speed jet two sizes higher. Can someone tell me where to get the proper jets for my carbs (preferrably internet...
  14. npd4432

    Anybody use boyesen reeds?

    Every year before I plop the boat in the water for the year I usually pick something to upgrade or repair. This year I have contemplated putting the boyesen reeds in the motor. Other than reading the company testimonials I have not read any real world objective opinions on them. Anybody have...
  15. npd4432

    Fast idle lever on control box

    It seems that my fast idle lever is not working. It will move up and down and prevent the shifter from going into gear when in the up position, but it does not move the cables when looking at the carb linkage. It worked fine last year and progressively got worse until it quit. It is also...
  16. npd4432

    Link and Sync for 75 HP Evinrude

    Can someone give me the instructions on how to linc and Sync the cables on my 1983 Evinrude 75 HP motor. Motor model # is E75TRLCTE.
  17. npd4432

    1983 Evinrude 75 HP high idle problem

    My motor E75TRLCTE is idleing high. it is between 1300 and 1500 at idle. How do I adjust this? The thumbwheel on the throttle cable is all the way in with no further adjustment. It also seems the "high Idle" lever on the control box may be stuck.
  18. npd4432

    Gearcase question on 1983 Evinrude

    I am currently looking for a new prop for my 1983 Evinrude 75 HP motor. The model number is E75TRLCTE. When bringing up the prop finder information two gearcases come up, one with 13 tooth spline "pleasure" thru hub exhaust, and a standard 13 tooth spline thru hub exhaust. In looking at the...
  19. npd4432

    cavitation/ventilation problem

    I have a 1983 Sportcraft Sportsman boat with a 1983 Evinrude 75 HP motor model # E75TRLCTE. The prop is a 13 3/4 x 13 Solas aluminum prop. The motor does have power tilt and trim. When turning at WOT the prop ventilates until you straighten it out again. This only occurres when turning at a...
  20. npd4432

    Lower Unit Water Intrusion

    This is driving me crazy!! I have replaced the gaskets on the drain and air plugs, changed the driveshaft seal and pressure tested and suction tested. Both tests check out good. I am still getting water intrusion. The only gasket I could think of is the shift shaft o-ring. Could this cause...
Top