Search results

  1. Lancerdad34

    Help with new Lenco Trim Tab Switch

    Lenco tech insists the new switch is not wired properly. Zoro Marine (Great Service) is sending me a new one. We shall see if the next one is right.
  2. Lancerdad34

    Help with new Lenco Trim Tab Switch

    Thanks for the reply! They are not! On the port side the black wire (Power) comes it comes out of 3rd pin down on the old harness. The new switch is the second pit down. On the starboard side the white to power comes out 3 pins down. The new one is 2 down. So this is sure confusing!
  3. Lancerdad34

    Help with new Lenco Trim Tab Switch

    I think it is something with the wires because I hooked up 12 volt directly to the port wires and it worked. I am quite lost at the moment. Something is different with this new switch. When I snipped off the power connector on the new one it used the pink wire one the starboard side and black...
  4. Lancerdad34

    Help with new Lenco Trim Tab Switch

    Well guys I am stuck! I connected wire to wire and now only the starboard trim tab is working! What could cause this? I am not sure how to proceed! Thanks, Brian
  5. Lancerdad34

    Help with new Lenco Trim Tab Switch

    Yes doing that today. Thanks for the help!
  6. Lancerdad34

    Help with new Lenco Trim Tab Switch

    No sir I intend on splicing it in with heat shrink connectors. Thanks for the reply.
  7. Lancerdad34

    Help with new Lenco Trim Tab Switch

    Yes no help from them! All they did was send me a wiring schematic. It looks I will have to cut off the old connectors and splice the new switch in.
  8. Lancerdad34

    Help with new Lenco Trim Tab Switch

    Last fall I broke up my trim tab taking of the panel wo work on speaker wire. I just ordered a new on amazon. The connectors on the new switch are not the same as the wires that were connected to the old one. I am lost here and sure would appreciate some advice on how to proceed. It is the...
  9. Lancerdad34

    New Garmin 93 sv wire directly to battery?

    Thanks good idea! It will just sit on the spool otherwise!
  10. Lancerdad34

    New Garmin 93 sv wire directly to battery?

    I am getting ready to install this garmin in my Sportcraft 241. I have a brand new spool of the red/black 14 gauge wire laying around. Should I connect right to the batter instead of going to the fuse block? When I connect to the new transducer to the old one to pull it thru I thought it...
  11. Lancerdad34

    Lenco trim tab switch

    Will try thanks
  12. Lancerdad34

    Lenco trim tab switch

    It all fell apart!
  13. Lancerdad34

    Lenco trim tab switch

    I messed up my switch taking off the side panel to replace speaker wire. Looks like about a $100 mistake. Anything I need to know when I replace it? Thanks Brian in Mi
  14. Lancerdad34

    Merc cruiser 5 0 backfire

    Thanks for the reply!
  15. Lancerdad34

    Merc cruiser 5 0 backfire

    4800 when it happens if I back off a little it goes away.
  16. Lancerdad34

    Merc cruiser 5 0 backfire

    Got it!
  17. Lancerdad34

    Merc cruiser 5 0 backfire

    If it did not do it when I test drove the boat why now? Have not been back to boat yet to check all that. Can check fuel filter then. Compression check will have to wait. That is a major undertaking I can hardly get my arms under to even feel the plugs!
  18. Lancerdad34

    Merc cruiser 5 0 backfire

    Thanks did not know there was a difference.
  19. Lancerdad34

    Merc cruiser 5 0 backfire

    One critical thing I forgot! When I test drove the boat in late July it did not do that! Thanks, Brian
  20. Lancerdad34

    Merc cruiser 5 0 backfire

    Thanks for all the replies! I guess I have to get into it deeper to find out!
Top