Search results

  1. J

    Where does it pee:)

    Thats how I've always expressed seeing the waterpump circulate. Anyways, where does it pee on a 1976 johhny 135?? Is it out the prop exhaust or the 1" square holes where the case meets the engine?? My 1971 rude 85hp had a pee hole on the side, but not this 135. Thanks as always - Jody
  2. J

    Need advise on batt chargers

    I have a 24v trolling motor (2 batteries hooked in series?) and of course the 12v cranking battery. The engine is a 1976 Johnson 135hp on an 86' glasstream 17ft angler. What can I do to keep the trolling motor batts charged while cruising. Yeah I can charge them out of the water, but I really...
  3. J

    Simple tilt/trim question, I hope

    76' 135hp Johnson. Getting ready to repair the tilt/trim and was curious: what is the electrical connector on the left outer ram if standing with motor in front of you? The previous owner had the wire laying in the bilge and I really want to do this right. I assume it may be a low fluid sensor...
  4. J

    Calco tilt/trim

    Been reading alot on here about the pump problems. Where is the cheapest place to get a calco replacement pump? The bad thing is, i dont know if the rams are any good either since this pump has been tore down by previous owner and not put back together. Thanks for any help you all may have - jody
  5. J

    Do I have tilt & trim????

    Was looking at this 76' Johnson 135 and I'm not sure it has trim. I only see 1 ram on each side of the motor, the calco pump assembly. I thought if the motor had trim there would be additional rams also. Am I mistaken??
  6. J

    135 JOHNSON not planing

    Okay folks, got rid of the wescraft and glastron ssv, bought an 87' glasstream 17' bass boat with a 77' (i think) 135 Johnson. Havent had it on the water yet since i have a few things to figure out/repair. Got it real cheap but checked it over pretty good. The motor fired right up, carbs were...
  7. J

    Floor Drain Holes

    Just Got This 79 Glastron Ssv-176. Previous Owner Redid Foam And Floor. I Dont See Where The Water Is Suppose To Drain From The Floor Out The Boat. Does Anybody Know Where The Drains Are For The Floor??? I Dont Believe The Owner Provided A Way For It To Drain. Suggestions????? Tia - Jody
  8. J

    Merc 1400 tilt/trim swap

    See this post: http://forums.iboats.com/showthread.php?t=373909 I wanna put the evinrude 85hp on the glastron while I figure out what is wrong with the Merc 1400. Whats it gonna take to install the tilt/trim onto the evin??? I havent even compared the two yet, so just trying to get an idea of...
  9. J

    How to do seats

    I will post pics of this project 79' glastron ssv-176 probably 2morrow. I need seats done and of course some interior panels done. Me and the family are going to do this. The main seats are from my old boat(reupholstered 2 years ago) and of course fold down to lounges, but the front and rear...
  10. J

    I Need Pics

    Starting this glastron ssv-176 project and would love some pics, specifically interior, so I have a better idea of what needs done. I have googled, not much luck. Its a 79' but a couple years before/after would probably suffice. tia for any help. Jody
  11. J

    Glastron ssv-176

    What is this boat considered?? Kind of a newb when it comes to boats. Is it a bow rider, utility, sport boat,etc?? I know its a vhull. Kinda wanna get a boat manual so I can start to work on this thing. Thanks for answering this stupid question....
  12. J

    Westcraft and Glastron

    Hi folks. 1st post here. Let me start off by saying that if you have a car/truck, I can fix it. Been turning wrenches for 20 years. But marine stuff - notta. So I've got myself into a project. Here we go : my inlaws gave me 1972 westcraft 16-17ft trihull with an 85 hp evinrude last year. It was...
  13. J

    **NEED HELP - what prop would u use

    Im thinking about using a piranha prop for my 17 foot monark bass boat with a v4 115hp yammy. The prop on now is a Michigan aluminum 13" diameter and pitch is unknown to me. Has 1010Q5 stamped on it. Anyway, what diameter and pitch would you guys use. Right now i top out at about 45mph but only...
  14. J

    HELP - yammy 115 - what year -HELP

    ok guys, heres a easy one for ya, i hope :<br />yamaha 115ETLN on one side and then on the other is this = 115AETO<br /> 6ES [L 351950]<br />has to be serial number right? can anyone tell me what year it is? it has V4 115 on the hood i just need a prop for it and most manufacturers...
  15. J

    YAMAHA 115 prop - What size??

    Just pulled prop off 115hp yammy, i believe is an 84', & dont have the slighest clue as to what the size or pitch is. Measured prop from center of hub to outer blade = 6 1/2" x 2= 13" right. Well the numbers on the prop dont tell me pitch. They are as follws : 1010Q5. What pitch is that. Help...
  16. J

    YAMAHA 115 prop - What size??

    Just pulled prop off 115hp yammy, i believe is an 84', & dont have the slighest clue as to what the size or pitch is. Measured prop from center of hub to outer blade = 6 1/2" x 2= 13" right. Well the numbers on the prop dont tell me pitch. They are as follws : 1010Q5. What pitch is that. Help...
View older results
Top