Search results

  1. B

    Remote control cable sets compatibility 1974 set on a 1977 Evinrude

    I have good set of remote cables on my boat that were to my 1974 Evinrude 115 hp that I just removed. I put on a 1977 Evinrude 70 hp. If the cables are good, is there any reason to change to the ones that came with the motor I bought? Are these remotes compatible?
  2. B

    Steering rod and steering arm connection hits port side of engine well. Any Fixes?

    After review, I realized I misstated the direction of turn. The photo is showing the motor in a full starboard turn, at least as full as it will turn, not a full port turn as previously stated I just put a 1977 70 hp Evinrude on my 73/74 Glasspar V165 hull. When I turn wheel to port, the end...
  3. B

    What is the best way to repair unused holes in transom when replacing a motor?

    I am going to have two holes I need to relocate for my new motor. What is the best way to repair the two unused holes left behind? If it matters, it's a 73/74 Glasspar V165 hull
  4. B

    Recommendations on a good speedometer system.

    I want to replace my speedometer system, it's pretty cheesy and old as well. I'm not looking for exotic, just an honestly priced, good working and reliable system. Any suggestions?
  5. B

    What is and who makes a quality boat cover

    Title kinda says it all. What is a quality/lasting boat cover? Who makes it?? I have bought various ones that seem to go to .... in less than a year. I do admit, wind is an issue here in CO. I uncover to transport. I just looked at the boat cover link auto inserted in my post, Glasspar is...
  6. B

    What do think of my fuel tank?

    This is a 20 gallon fuel tank off my boat I just pulled it to replace the motor. This is all external damage, no leakage from tank at all!! I can inert the tank and grind out most of the rust, use a rust neutralizer on the rest, prime and repaint. Any and all opinions welcome? By the way...
  7. B

    Is this a stainless steel or aluminum prop

    This is a 13 1/4 x 15 prop I believe it to be stainless steel. Am I correct?
  8. B

    Steering cable compatibility and removal and install 74/77 115/70hp Evinrude

    I'm pulling my 115hp 1974 Evinrude and replacing it immediately with a 70hp 1977 Evinrude. (1974 Evinrude 115hp Model # 115493B, 1977 Evinrude 70hp Model # 707739) I have a new, been on the water 4 times, steering cable already installed on hull. Since I am already pulling and replacing...
  9. B

    What is best way to service used remote cables prior to install?

    My new to me 1977 70hp Evinrude came with what are supposed to be a good set of remote control cables. I'd like to know their condition prior to install as opposed to the dreaded LATER!! What is the best way to test and service these prior to installation. a couple photo's
  10. B

    Can't upload photo's

    Starting yesterday, I am unable to upload any photo's for my posts. Have correct format etc. Can you have to many photo's uploaded, or are there restrictions based on level? OR? All help is appreciated!!!! The message just says "upload failed", no other explanation.:confused::blue: Maybe...
  11. B

    Propeller compatibiliy Evinrude 77 70hp and 74 115hp

    I have a 1974 Evinrude 115hp Model # 115493B that is totally shot and being replaced by a 1977 Evinrude 70hp Model # 707739. Will my very nice near new stainless steel prop from the 115hp fit the 70hp?
  12. B

    What is the best sealant for sealing motor mount holes?

    I usually use pure silicone for most water tight sealing requirements. What is the best sealant for sealing motor mount holes during motor replacement? After all, we're not sealing the kitchen sink!
  13. B

    How to Power wash / pressure wash an outboard motor

    Odd, I searched the forums for info about power washing or pressure washing (your choice) an outboard motor and found nothing!!?? So thought I'd start one. I just bought a nice condition 1977 70 hp Evinrude outboard. As you might expect, in all the right places there is grease, fuel and dirt...
  14. B

    Mounting bracket compatibility question For Evinrude 77 70hp and 74 115hp

    Would the mounting bracket holes for a 1977 Evinrude 70 hp model # 707739 line up with the existing holes on a hull which are from a 1974 115hp Starflite model #115493B, or would I need to drill mew holes and deal with he old holes?
  15. B

    Replacing Impellers/water pump on a 1977 Evinrude 70 hp Mod # 707739

    I am going to hopefully finally buy a motor for my 16' boat. I am looking at a 70 hp this time. It's an Evinrude, 1977, 70 hp, mod #707739, (two model #'s that year 70773/70779 as listed in engine ref chart.) The motor has sat for three years. Plan on doing some carb work, not sure how...
  16. B

    1978 85 hp Evinrude Model #85899 Photos for review and opinions

    In my previous post, "1979 Evinrude 85 hp Model # 85999c $800 is this high or low?", it was concluded by all that this is a 1978, not a 1979. Current owner corrected Mod # to 85899 and along with the 1517cc on lower unit makes it a 78. I am going to look at and run this motor on Saturday...
  17. B

    1979 Evinrude 85 hp Model # 85999c $800 is this high or low?

    I have a chance to purchase this 85 hp Evinrude Model # 85999c for $800, does include a boat, don't want it but will have to deal with that. I am told it is a good running motor. Will see and hear it run prior to purchase. It works as a good replacement for my shot 74 Evinrude 115 Starflite...
  18. B

    Evinrude: MODEL # E155WTLEIB Looking for information on this motor.

    I have an opportunity to purchase this motor. It is I'm told a spare Coast Guard motor with only around 10 hours on it, mostly testing in fresh water. Below is the information I know based on model # provided by seller. Serial # is G02959591. The information is from Evinrude.com model look...
  19. B

    100 hp Evinrude, 1972 model 100293R Is it worth $1,200 with slow start issue?

    I have a chance to buy this 100 hp Evinrude, 1972 model 100293R, would fit my boat nicely, had a 1974 115 Starflite before. I am told it runs nicely at all RPM's, even low idle, but starts hard occasionally. Barring no deception on the part of the owner and condition is as stated, would this...
  20. B

    Would you buy a 1968 65hp Johnson Electric Outboard?

    I have a chance to buy a good working 1968 65hp Johnson Electric. Asking price $500, includes a boat in need of repair (junk). Already have a boat I like. Currently have an 83 Evinrude 115 hp Starflite, currently not working, numerous issues! Thinking of downsizing. Is this a good buy or...
View older results
Top