Search results

  1. homelite

    Westerbeke 4.5 BCGTC Generator 1999

    I need a float for the carb. Or a used carb. I can't believe how popular these were, esp in Sea Ray in those years, but I can't find any carb parts for the Weber carb. The Westerbeke PN is 42776 for the carb. the parts list does not show a PN for the float for some reason. TheWeber carb...
  2. homelite

    Inboard/V drive prop shaft runout

    I have a slight vibration in a Sundancer 340, twin V drives. I see a slight wobble to the port shaft where it comes through the log at the seal. I assume if I see it with naked eye, it's too much but what is the spec? I con't find anything published.... Also, who straightens shafts in the...
  3. homelite

    Pulling 1999 Sea Ray 310 V drive engines/Velvet trans

    I need to pull an engine. I see the mounts to the floor are on the engine and then on the trans with bell housing holding it together. Is it common to pull one or the other and block up the component that you are not pulling? Or must you pull both engine and trans, then separate once removed...
  4. homelite

    noisey cruiseair a/c compressor

    Is it common to replace the a/c compressor? I have an hvac guy that said no problem. My compressor is noisey. Works fine, but bothers me. It's a 1999. Just wondering. I in no way need a complete new unit for 2500.00! I don't see them in parts sections or talked about..... Thanks in Advance.
  5. homelite

    4 hp Force- 1985 driveshaft install in lower unit

    OK, so I'm replacing an impeller, a simple job, right? I can't get the driveshaft back in the lower unit. Does the pinion fall out of place? I shake it around and something is rattling..... No gear oil is in there. Do I just play around until I get the pinion in the correct spot to get the...
  6. homelite

    Force single cyl 4 hp- 1985

    Hello, Can some supply me with the proper breaker point gap? The onwers manual does not list it. Also, an aftermarket water pump impeller brand and part number. Thansk, Scott.
  7. homelite

    1999 Sea Ray 310 DA w/soft deck (hood) in front of center hatch (to windlass)

    Hello, On the said boat that I just purchased, i noticed when I walk on the deck it is soft. In talking to a fellow boater at my marina, he suggested the wood may be rotten under the fiberglass deck. I think he is correct, even though no leaks or smell. Questions: How to remove headliner in...
  8. homelite

    Timing set procedure for 1999 350 Mag Bluewater Inboard s/n OL302291

    Can someone provide me with the Mercruiser procedure for this setting/adjustment? I have a techmate. It's just that my seloc book only goes back to 2001 and I just bought a 1999. The Mercruiser owners manual that came with the boat says 8deg but does not say how to check it??? Thanks,
  9. homelite

    1999 350 mag mpi bluewater inboard seawater pump wear plate

    S/N is L302781 Question is, my seawater pump wear plate is pitted a bit. Noticed while routine impeller change being made. Can I flop it over like a pancake? Can I use the other side which is virgin? The circular wear is not that bad and I have a new double D seal where the wear plate...
  10. homelite

    V drive drive shaft removal help needed. 1999 310DA

    Hello. I am new to v drives, but am a mechanic. I am trying to remove my prop shafts on my 1999 310 Sea Ray Sundancer. It has the Velvet 5000 transmissions. I have the cotter pin and large nut off the end of the shaft (at the transmission). I removed the 4 bolts securing the coupler to...
  11. homelite

    1999 Sea Ray Sundancer 310 V Drive propshaft seals

    I just bought the above. It has 300 hrs on it. I never had an inboard. I am a certified auto technician so I just need pointed in the right direction. First of all, there is a raw water 3/8" hose feeding the seals. I assume to cool them. Questions are: How to get in there? I'm mid...
  12. homelite

    2000 280 GS-I with TBI

    After a hot run which the engine runs perfect, when the boat is docked, shut off and sits for the night. On the next day first start up, the engine runs rough for 15 to 30 seconds, sometimes till you rev it a bit. Then it smooths out and runs perfect all day. Been doing this for some time...
  13. homelite

    Mercathode System Current Draw

    Does this system draw current when dry such as being on the trailer? Or, does it only draw current when wet? Thanks
  14. homelite

    2003 350 mag serp belt shredding

    Boat had 60 hrs when I purchased. Had a NAPA (25-061066) belt which surprised me...... Anyhow, maybe I see why now. I am seeing "belt chips" all over the engine area. I installed a new NAPA belt and it's happening in 5 hrs. It's going to fail. Any TSB's I should know about? I imagine...
  15. homelite

    2003 350 Magnum MPI IAC whistle

    I installed a new engine over the last few months. While cleaning parts and the Throttle body, I found a scotchbrite pad type of torn up material I assume was a siliencer. It was so rotton and worn, I tossed it in the trash. Now the engine is done and running great, but has a high rush of air...
  16. homelite

    2003 350 magnum popping through intake at 3400 rpm

    I installed a new marine GM long block (not a reman) from a a reputable distributor. Did it right. New exhaust manifolds, elbows, plugs, wires, cap rotor, etc. I must say, I'm an ASE certified auto mechanic and know what I am doing, but I am getting stumped, as is another tech friend of mine...
  17. homelite

    2003 350 Mag bravo 3 steering still/tight

    I have the condition listed above. Boat sat 2 years and I just got it running. Was dissappointed with P/S. Hard to steer with one hand, esp with docking. Unhooked cable and it turns very easy so that rules out the rack and cable. I'm comparing it to my VP 280DPS I used to have which would...
  18. homelite

    2003 350 Magnum Bravo3 tach inop and warning alarm beeps every minute

    Hello. I bought this boat with a bad engine. I installed a new long block, manifilds, risers, the entire 9 yards. $5500 worth. Did everything right. Started today. Runs great but the tach does not work and Ihave the lettle red alarm beeping every minute while engine is running. I have no...
  19. homelite

    bravo 3 shift cable bellows contacts gear lube monitor hose on right turns

    Replacing the bellows. Ddidn't notice this when I took apart but upon putting together, I notice the gear lube monitor hose really cramps up and pushes on the shift cable bellows on right turns. I can't see any other issue and it must have been this way before? Just want confirmation as i...
  20. homelite

    2003 bravo 3 lower shift cable barrel

    I have this apart and can't seem to turn the brass barrel. Sounds dumb but even when holding the cable with vise grips I still can't and don't want to damage anything. Am I missing something? It shouldn't be tight at all. Thanks.
Top