Search results

  1. D

    Cockpit side rail cushion??

    in the cockpit the cushion that is about 6 inches wide and about thigh high 4 to 6 ft long is there a name for this? mine have been all removed i need two 6 footers and one 5 footer i was wondering if someplace sells these all ready made or do i have to fabricate and sew and buy the cushion...
  2. D

    OMC Exhuast Flapper goes which way?

    350 5.7 with y pipe I believe they go hinge up correct and the little rubber hinge things that the pin goes thru do they go from the outside of the y pipe pushed in or put them on the inside pushed out?
  3. D

    High rise exhuast manifolds

    Im going to replace my old OMC log style manifold and was going to get the High Rise style that are advertised that these replace the ones I have and are more efficient. I have a 350 5.7 gm motor with the cobra sterndrive pump only,,, no inside raw water pump,, has anyone used this style...
  4. D

    rawwater cooling

    Well I have read the pros and cons but alot of post are close a liitle off to my situation but heres my question.Just had my nice 350 5.7 motor all new and rebuilt and had originally planned on installing a 800 dollar fresh water cooling system for block only.( I dont have a separate pump...
  5. D

    omc flapper valve

    I have a omc cobra sterndrive motor is a 350 5.7 boats a 1989 I took out the engine and noticed there are no flapper valves in the Y pipe so I ordered two part# 985749 with a cross of # 3853864 Thought they were the ones but they are way too tight will not slide down the pipe now i see...
  6. D

    trim cylinder lines diagraham

    I have a 1989 cobra outdrive I just replaced the transom assembly and I just want to make sure the lines from the rams are connected correctly all the way to the trim motor on the inside.. are there any diagrahams. my seloc doesnt show it . what I thought was the up now im not sure thanks
  7. D

    water temp sensor

    would this be the right one Part # 18-5898 for a 350 5.7 omc cobra sterndrive?
  8. D

    petronix flame thrower black expoxy marine coil

    Has any one used one of these? I do have the petronix distributor set up and need a new coil . I guess this one throws out 40,000 volts as apposed to a standard coil 24,000 and was wondering if there is such thing as too much juice in a coil,,,, New rebuilt 350 motor and I dont want to fry a...
  9. D

    Spark Plugs

    any suggestions and what size ,,,I just got the engine back last week rebuilt ,,He used a different block its a chevy 1995 5.7 350 bored 30 over says it 305 hp all rebuilt to marine engine specs etc,,, but need plugs this morning ,,, seems to be a ton out there but want to make sure I get...
  10. D

    Heat exchanger

    Is it possible to just buy a used heat exchanger (for the same size motor ) and modify so it cools the block only. I have a new motor sterndrive set up (RWC) so I have heard a full sysytem shoudnt be done without a sep seawater pump.I want to make it a fwc system,,,the kits for my omc motor...
  11. D

    electronic ignition

    5.7L (350 ci) Delco Voyager EST Marine Electronic Distributor Kit.... I currently have the petronix style on the 350 5.7 305hp but i saw this set up and was wondering is it worth the 319 dollars to change...I havent installed the new rebuild yet and was looking to replace wires when I...
  12. D

    Fuel Pump Electric or Mechanical?

    Just got the new engine back(350 5.7) from the rebuild and Im doing alot of other things but what I noticed is the fuel pump that I left in the bilge connected to the fuel line is an electric blue holley set up looks rusty etc and kinda mickey mouse line connections I think it does have the...
  13. D

    OMC cobra outdrive wont move LEFT OR RIGHT

    its a 1989 cobra 5.0 350 i/o with power steering (engine is removed new one waiting to be put in) and I couldnt get it to move at all trying it from the wheel so I did all the trouble shooting, cable greased and it moves freely when diconnected from acutator and the ram works fine when its...
  14. D

    bolt pattern

    I have a 23 ft hyrdasport and it has gil drive. I just took off the blown evinrude and want to replace it with a 250 hp 2003 hpdi yamaha...one ..how is this motor? and two will it bolt right on? is the pattern to mount on an outboard pretty much standard pattern? also I saw another one with a...
  15. D

    Info on this 03 motor

    any info on this motor F250FPXSTA SERIAL# 05015847 its a 03 250 evinrude ficht ram injection can some of you experts run the serial number to tell me what if anything has been done on this motor thanks
  16. D

    head gasket

    do they make extra thick headgaskets for my motor I believe they will have to shave off the block alot of material so I was wondering if they are available,,,its a 1996 evinrude 200hp ocean pro 200TXEDR thanks also head bolts do you have them here?
  17. D

    flywheel removal update

    I have 1 1996 200hp evinrude it took 4 days to get it off and one broken balancer but after buying a new harmonic puller and tightening the bolts till they almost snapped i let it sit in PB blaster for the three more days yesterday i tappped lightly for about 2 minutes on the balancer shaft and...
  18. D

    MANUALS

    anything out there that shows detail and step by step procedure for rebuilding a 1996 evinrude 200hp,,,i have one manual for the 1996 but it skips so much detail
  19. D

    rebuilding

    1996 200hp ocean pro ,,,couple of questions Dhadley why do you always point out that it is the number 2 piston that goes??what is the common cause that makes that piston heat up?? I have mine apart and i was going to have my buddy mechanic and I put new pistons and rings etc in,,,should I send...
  20. D

    replacing 200hp evinrude

    My 200 hp 1996oceanpro evinrude went last year Im thinking of rerbuilding but I have a chance to buy a 250 1998 oceanpro with good compression and low hours,,it comes with all the controls and harness ,,,can I just bolt it on my boat and hook it up? is weight an issue? my boat is a 23ft...
Top