Search results

  1. J

    Evinrude Starter rotation direction

    I purchased a 1977 85Hp Evinrude motor. Model 85-799S The starter goes around but does not engage the flywheel. I charged the batteries for 24 hours. The starter gear rotates in a counter clockwise direction when I turn on the ignation. When I manually turn it the other direction (clock wise)...
  2. J

    Installation of CMC power tilt and trim

    The power tilt and trim on my 85 hp Evinruide motor needs to be replaced. I am looking at using a CMT PT130. How difficult is the installation? Can I remove the motor with a floor jack? If so how do I do that? How much does the motor weigh? The shop wants over $1000 to install.
  3. J

    Prop replacement for 4hp Evinrude 1969

    I have a 4HP Evinrude Model 4906B. I think it's a 1969 . During shipping UPS broke the prop. Where can I find a replacement which will fit?
  4. J

    Spark Gap Evinrude 9.5

    I have a 9.5 Evinrude and it says on the flywheel set at .02. Is that for the points or the plugs? What should the gap be for the sparkplugs and is that inches or mm.
  5. J

    9.5 Evinrude will not run with choke open..has to be almost closed

    I replaced the carb. Took out the sparkplugs and sprayed Seafoam into them. Then I had to put the motor into gear to start. I closed the choke and it started. I put additional seafoam into the carb and it almost immedieately started purring like a cat. I tried to move it back to netural and...
  6. J

    Removal of Fly Wheel 9.5 Evinrude

    What is the best ways to hold the fly wheel from turning when trying to remove the top nut? I am going to Auto Zone to get a harmonic puller and the bolts.
  7. J

    Old 9.5 Evinrude Carbubrator 9222M

    I have an old 9.5 Evinrude motor model nbr 9222M. The carburator leaks at a mfg 1/8" hole on the side. It looks like it should have a plastic plug like in picture #2. What is the year? Do they make the plug for the hole? Do they still make the Carb Can I use JB Weld to plug the hole. The...
  8. J

    Water Pump for E15ECRM

    I just purchase an Evinrude 15Hp Ele. The ower said it worked okay. When I put it in a barrel, there was only a fine spray of water coming out of the pee hole. I ran a weed eater line down the pee hole without any difficulty. I hooked a hose to the pee hole and back flushed the unit with water...
  9. J

    9.9 Will not Shift until I turn Flywheel

    I have a 9.9 Johnson (J10ECES) It will not shift from neutral to forward or backward until I turn the flywheel about 1/2 turn. I can put pressure on the shift and turn the flywheel and feel when it makes the connection about 1/2 turn. It only allows me to shift that direction and still...
  10. J

    1977 Evinrude Trim will not hold

    I just purchased a 1977 Evinrude motor on a 115 Spitfire boat. It runs great but the trim will not hold it's position. Do I need to replace the cylinders, repair them, replace the power trim motor? Thanks,
  11. J

    Water Pump for 1970 20 HP Johnson

    How difficult is is to replace a water pump on a 1970 20 Hp Johnson? Is there anything else I would need to replace while I am in there? I have replaced them on 91/2 johnson's before.
  12. J

    How to Put Fuel Pump together for Johnson 20 HP 18-7823

    How do I put the attached fuel pump together. It is for a 20HP Johnson 1970? There was not any instructions for the 18-7823 kit
  13. J

    Evinrude Age Unknown need Fuel Pump kit

    I purchased a used Evinrude 20 hp and it runs for about 5 seconds then almost stops, then goes again. I can pump the hand bulb and it will run ok but the bulb takes a while to fill up again. I am looking for a fuel pump kit. It has on the fuel pump 322-981 and is about 1-1/12" square. The...
View older results
Top