Search results

  1. jim kinser

    Question ??

    Would like to know where the oil warning module mounts. I'm putting a 1994 mariner 60hp together that someone else took apart. A picture would help. Thanks
  2. jim kinser

    Elgin/McCullock

    I'm in dear need of pt# 73055 or 18-3009. Impellor for a 7.5 hp elgin, 1963 vintage.
  3. jim kinser

    fuel pump ?

    Looking for check valves for 385784 fuel pump.
  4. jim kinser

    idles ok

    I have a mariner 40c 6e9 515698. Idles good, rev it up and it sounds like it runs out of fuel, I kited the carbs, getting fuel ok, getting fire ok. I subed the fuel line and tank, same thing. Could it be ignition ?
  5. jim kinser

    need carburator

    I'm looking for a bottom carb for a 1995 40hp 4cyl carb number WMA-10. This carb has the large half round float cover and the high speed jet holds it on. Anyone have one ? All I need is the casting, tore one apart and someone had broken the part off that the float pin goes through. PM me if need.
  6. jim kinser

    lu seal kit

    Replacing seal kit in lu on e225fplssc. Got three numbers, 5000411, 5006373 and 18-8384. Which do you recomend, and are they the same ?
  7. jim kinser

    Ringing question

    :confused: I'm rebuilding a 1996 200hp merc, bored two cyl. My question is ; will wisco or sierra std rings work on oem std pistons ???
  8. jim kinser

    318 ???

    :confused: I need the ignition timing setting and where the timing marks are on a 1977 chrysler 318 / 225 hp. Thanks
  9. jim kinser

    Over heating 1990 60 hp

    :confused: I have a 1990 60 hp johnson that over heats, I've changed water pump assy (impeller, cup, plates, gaskets) changed exhaust housing, pulled power head changed gasket, pulled head, pulled exhaust cover, still over heats. Water does come out of pee tube good. Could there be a...
  10. jim kinser

    Faria tach question

    :confused: TC9031A Anyone got a new number for this tach ?
  11. jim kinser

    year hp ?

    I have an evinrude, the only numbers on it are 6039-25264. Anyone know hp and year? It's a complete engine.
  12. jim kinser

    9.5 problem

    I have a '67 9.5hp johnsn that runs ok for a minute but won't idle. It acts like its starving for fuel. I cleaned carb, replaced fuel line from pump to carb, it pump fuel ok, it's got 65 lbs compression. Any suggestions ?
  13. jim kinser

    part number

    Does anyone know what the part number for a rod, # 322212 is cast into it, but nowhere is this number to be found. It's for a 1981 60 hp johnson mod #J60ELCIA .
  14. jim kinser

    Mercury Gear case

    I have a 40 hp merc Ser # E311774 with a bad set of gears. What I need to know is if part #'s are compatable. Part #'s are; 1682-821306T6 and 1682-821306T28 . The only difference I can find is gear ratio.
  15. jim kinser

    Mariner ???

    :confused::confused: Can anyone help ? I have a 200hp Mariner Magnum Ser # 39855211, what year was it built ?
  16. jim kinser

    Mariner year ?

    :confused: Could anyone tell me the year Mariner was built, it's a 200 EFI ser# 39855211.
  17. jim kinser

    thermostat question

    :confused: I think someone put thermostat in wrong. 1985 5.7L mercruiser. Does the thermostat go in the block or the thermostat housing ? I looked for a tech handbook on this but could not find one in pdf.
  18. jim kinser

    Engine questions

    :confused::confused: Having problem with engine running at idle. I cleaned carbs on a '87 85hp Force Mod # 856F7B and these parts are missing. #19 and #22 were not there. Carb part #'s are what are called for in the picture. Did someone leave them out ? Or what ...
  19. jim kinser

    carburetor orifices

    :confused::confused: Can anyone tell me the difference between a 61C and a 61D high speed orifice. As far as I can tell, there is no physical difference. I'm rebuilding a '77 140hp and I discovered it had a 135hp carburetor on it. It may be a '75 135 hp instead. There are .030 and .032 low...
  20. jim kinser

    Carb Jets ??

    :confused::confused::confused: Does anyone know the difference between a 61C and a 61D high speed jet ? I cannot find any difference.
Top