Search results

  1. cecho

    Installed Torque Shift Prop today...

    I love it! :D Engine goes right up to about 4K RPM and slowly goes to 4400 RPM by full throttle. Getting out at the hole at full throttle while at a high RPM is really a great feeling. The prop is also allowing me to plane about 5 MPH slower than my 17 pitch prop did. The prop works amazingly...
  2. cecho

    Engine won't start anymore.

    Re: Engine won't start anymore. Your fuel filter is number 29 in this image
  3. cecho

    Ethanol in fuel

    There are two gas stations in town that sell pure gasoline, but they are several miles out of the way. Is it worth taking the boat there to fill up to avoid putting gas with alcohol in the fuel? I'm curious about what people's opinions are on that.
  4. cecho

    Play in steering

    I've got some play in my steering I'd like to get out. The outdrive will move side to side a few inches. I do not believe it's the gimbal ring or steering arm. The gimbal ring is tight on all four "corners" and I do not see any play between the steering lever and the swivel shaft or gimbal ring...
  5. cecho

    140 vs 160 degree thermostat in open loop fresh water cooled engine.

    I'm pretty sure my boat has a 140 degree thermostat. Would there be any problem with putting a 160 on it? I know that's bad in salt water, but what about fresh water? It seems running the engine at 160 would be a lot better than 140, but I doubt using a 180 would be safe for the engine...
  6. cecho

    Rewiring trailer, should I had Aux 12 V+ to charge boat batteries?

    I'm charging the plug on the vehicle and trailer to the 7 pin blade. Since it includes 12V+ Aux, should I go ahead and use that to help charge the boat batteries while towing? The trip to and from the lake is 45 mins. I have two deep cell Group 24 batteries in the boat.
  7. cecho

    Merc 898 WOT RPM range: 3,800 - 4,200 rpm. Why?

    I'm wondering why the 305 is limited to this range while the 350 of the same era is limited to 4400-4800 RPM. Is it the camshaft profile? Is the engine not capable of higher RPMs? Is it the outdrive? Will I leave the power range for the engine if I go above 4200 RPM? Edit: P.S. I just...
  8. cecho

    A few questions about Land & Sea Torque Shift

    I just received a newer (1/2 inch pins) 26? Torqueshift prop and disassembled it for inspection and cleaning. I was wondering what the best way to set the pitch screws back to the initial setting is. I have no clue what the maximum in or out setting on the screws are supposed to be. Also, is...
  9. cecho

    Quote to replace shift cable.

    Re: Quote to replace shift cable.
  10. cecho

    Installing SE106 in place of MC-1

    Re: Installing SE106 in place of MC-1 Archive of the "old" internet? There won't be an archive to the "old" internet. It'll be called The Overlord's Past Memories after Google takes over. :behindsofa::tinfoil3:
  11. cecho

    "sticky" trim gauge

    Re: "sticky" trim gauge Those gauges look very familiar and are of the same color, but the temp gauge has degree numbers, the oil temp shows PSI numbers and the volt gauge has a 12 in the center. I found an image of the trim gauge. I was wrong about the orientation. It is orientated...
  12. cecho

    Need new brake shoes.

    How do I find out what kind of brake shoes I need for my trailer?... and where to get them from. I pulled the drum off to re drease the bearings and found the front shoe had delaminated. It's a 78 EZLoader with surge brakes and drums only on the front.
  13. cecho

    "sticky" trim gauge

    The trim gauge seems to be "sticking" at the bottom of movement. It works fine once it start moving but if it hits the bottom (like when turned off) if stays there until it gets enough force to move to full up. Is it possible to take apart and clean the inside of them without ruining? It'd be...
  14. cecho

    Installing SE106 in place of MC-1

    I'm planning on getting a new SE106 to replace my damaged MC-1 soon. I had a few questions about it. Is there a mercruiser manual that best works with the SE106? When installing a new outdrive do I need to readjust the shift cable? Is there a break in period for a new drive? What is the...
  15. cecho

    AAA type service that will also tow the boat home?

    Can anyone recommend a service that will tow my truck and boat home if I suffer a breakdown?
  16. cecho

    Quote to replace shift cable.

    I called a local marine place asking for a part and was curious what they charged to replace a shift cable on an MC-1. I was quoted 4-5 hours of labor + parts with a 3 week lead time. 4-5 hours seems rather high. How long does it really take for a shop to do the job? I would have guessed a pro...
  17. cecho

    Swivel Shaft Grease Fitting on gimbal housing seems to lead to a black hole.

    I've pumped 20 pumps into the grease zerk at the top and it doesn't seem to be going anywhere. Any ideas? If I had to guess, I'd guess there's a whole buncha grease in an empty cavity up there and that there's too much old grease to let the new grease come out the bottom. Swivel Shaft Grease...
  18. cecho

    Choke 12V+ to Ignition Coil 12V+

    Is there any problem with running a jumper from the 12V+ on the electric choke to the 12V+ terminal on the coil? My new coil and ignition don't need the resistor wire and this is the easiest method to deliver 12V+ to the pair. It's what I'd do on a car, but I don't know if there's anything wrong...
  19. cecho

    Trim Sender through transom shield bolts.

    Getting the bolts off was easy since the wires fell apart and I had access to the top bolt. Now that I've tried to put them back on I've run into trouble. The bottom bolt was easy to access and I've torqued it to 100 inch-lbs, but there's no way I can get to the top bolt. I've turned the top...
  20. cecho

    Corrosion/pitting on bell housing bellows surface and shift cable threads.

    I'm getting ready to button things up and install the new shift cable and bellows. While cleaning the bell housing thoroughly I found two problems. Bellows Surface: This is the bottom of the bell housing bellows "seat" where the water was sitting. Is this going to pose a problem? Should I try...
Top