Search results

  1. J

    1998 115 reed/intake noise VIDEO ADDED

    I just rebuilt my 115 crossflow and it is sitting on my work bench! I have the carbs off and was turning the crank to check for binding ect ect and it turns smooth. However it is making a noise out of the top left intake hole like a backfire would sound like. if I put the palm of my hand over...
  2. J

    Do I need to rejet my carbs?

    I'm rebuilding my 1998 115 evinrude crossflow. I have 3 cylinders bored 20 over and one is bored 30 over. Do I need to rejet them or will the originals bo ok?
  3. J

    replace rings or not?

    I rebuilt my 1998 115 crossflow back in 09 ran great! well this season I put a new set of head gaskets on it, and the first trip out the port side gasket leaked water in. It must not have gotten a good seal. So now I got the block torn down and had to have the port bottom cyl bored to 30 over...
  4. J

    1976 evinrude 9.9 eating plugs

    I have a 1976 evinrude 9.9 modle 10624H. It eats up spark plugs like crazy. If I put in a new set of plugs (marine champion Ql77jc4) motor will run great for a few hours 2-4. Then motor will feel as if its loosing power and when put in nuteral and reved up it is slow to get to full throttle as...
  5. J

    crossflow crankshaft ??????

    I have a 1997 115 evinrude crossflow. I need a new crankshaft and was wondering what year motor I could steal a crank from. Evinrude parts shows a part# of 0434769. As far as i can tell that crank is only used in motors from 1992 to 1998. But I find it hard to belive that is the only crank that...
  6. J

    fast track tilt&trim HELP

    I have fast track tilt and trim unit that was a spare it is like new I pulled it out of the garage where it was sitting for a year or two and wanted to test it out well the tilt and trim goes up fine but only the tilt goes down the two trim shafts wont go down uless I push them down but when I...
  7. J

    115 crossflow head gaskets

    I have a 115 evinrude crossflow 1995 I rebuilt about a year ago. I just got it out of storage getting ready for the season. I noticed there is salt all around the head's like the gaskets are seeping. compression is 120 on all 4 cylinders I had them all bored 00.20 over, seeing as the gasket are...
  8. J

    cable cover

    I am looking for some type of cable cover to cover the wires and cable's going from my center console to the motor. They cant go under the deck so they are laying on top of it. I would like a cover to put over it to step on ect and keep the wires out of sight any ideas?
  9. J

    rust on welds?

    I have a galv triler i had the crossmembers replaced and where they welded them to the frame I used the cold spray on galv it worked fine for a month or two but I am now starting to see some surface rust. This trailer see's salt water alot! what do you reccomend to stop the rust?
  10. J

    1998 115 carb jet?

    I have a 1998 115 evinrude crossflow i rebuilt.I had all 4 cyls bored 30 over. I read a remark on this thread that I should up the jet size by two. I currently have the stock one in and it seems to run and idle fine. Any thoughts?
  11. J

    Interlux paint HELP needed

    I am painting my 18 foot skiff with interlux perfection. I am in the process of priming it now with interlux primekote. I put on two coats of the primer,sanded between coats and i am using the roll and tip method, and I am getting fine brush marks when i tip it. I am using a 4 inch white china...
  12. J

    rub rail

    I am looking for a cheap rub rail to put around my 17 foot skiff. I dont want to spend 300 on a taco kit just looking for a solid piece of half round or somthing like that.so i can screw it in to the rail to make it look good and protect it as well. any ideas?
  13. J

    stator??? or something else.

    My 1998 evinrude 115 is acting up. Cold start no throttle just a quick hit of the primer and it fires up but spits and sputters for about 30 secs till it warms up then idles GREAT! If i try to rev it up during the first 30 secs it dies but will fire right back up and spit and sputter. It will...
  14. J

    paint prep

    I have this fiberglass boat, and I want to give it a fresh paint job. However I cant get the old paint off. I have tried marine paint stripper didnt work I tried 60 grit sanding it did smooth the surface but didnt remove the paint I even tried sand blasting NOTHING. I would just paint right over...
  15. J

    which paint?

    I want to paint my 18 foot fiberglass boat with the roll and tip method. Do you reccomend the rustoleum or the inturlex brightside? thay are roughly the same price. But how about easy of applying them and durability?
  16. J

    HELP with boat edge

    I have this 17.5 foot fiberglass boat i have been doing alot of work to. It has a lip on the edge and it is very thin. So when it bumps into a dock or marker it craks the fiberglass. Now it is hollow underneath and I have thought that maybe if i put something up inside there to make it more...
  17. J

    1998 115 timing

    I cannot get my timing set on my 115 rude. The book i have (seloc manual) is very vage in this subject can anyone point me in the right direction IE a better maunual or something on the forum that goes into more detail? I am looking for some help other than just keep playing with it until you...
  18. J

    98 115 wont start?????

    1998 115 v4 crossflow rebuilt approx 1 yr ago 112 psi all 4 cylinders. Just rebuilt carbs I know its getting fuel, when i take the plugs out there wet with gas. It is getting spark when i take plugs out and lay against block there is good spark. replaced the stator still nothing. I did get it to...
  19. J

    90 hp rude (PEEING)

    I have a 1998 90 hp rude with a brand new waterpump. I pees out both exhaust holes and the hole coming out of the exhaust plate like no tomorrow! However when i put it in gear it only pees out the exhaust hole. Is this normal? as soon as i put it back in nutureal it pees out all three holes...
  20. J

    carb jets

    i found the jets in my 1998 115 carbs to be wrong. It appears the carbs are from a 1996 115. I bough this motor seized and rebuilt it. Since the rebuild it has not idled right or reved up. it coughs and stalls. I was told to check the jets so i did and they are the wrong numbers. I am suppose to...
Top