Search results

  1. newtoboat101

    Trim pump wiring acting opposite

    yes ,your correct trailer button thank you
  2. newtoboat101

    Trim pump wiring acting opposite

    what does 4th wire do,i can see where it connects
  3. newtoboat101

    Trim pump wiring acting opposite

    i will check that ,little in depth i took an old plug end that goes to 3 switch cut wires and put plug in pump with spliced wires i tapped blue with red ( red is positive) the drive goes down ,when i tap red and green together drive goes up ,so i think this why my 3 switch only raises outdrive...
  4. newtoboat101

    Trim pump wiring acting opposite

    Hello. Added new trim tilt pump and new cylinders and was adding a 3 button switch which I was not been able to get it to work properly so I went back to my old wiring and toggle switch. . so I was multi metering and alligator clip check and for some reason the blue wire brings my outdrive all...
  5. newtoboat101

    ALPHA 1 GEN 1 TRIM CYLINDER (NEW)WILL NOT GO ALL THE WAY DOWN

    bought both pump and trim cylinders from SEI ,don't see any trim limit spacer ,in description
  6. newtoboat101

    ALPHA 1 GEN 1 TRIM CYLINDER (NEW)WILL NOT GO ALL THE WAY DOWN

    Yes old ones went down further than these ,they did not bottom out ,but the angle of my outdrive was more down ,now it looks to be ,with new pistons sitting at the out trim max. the cylinder retract to 21 1/4 inches center to center nut to nut
  7. newtoboat101

    ALPHA 1 GEN 1 TRIM CYLINDER (NEW)WILL NOT GO ALL THE WAY DOWN

    thanx for down line confirmation ,when operating properly they do not go all the way in ,but mine are coming up even short of that by 2 to 3 inches
  8. newtoboat101

    ALPHA 1 GEN 1 TRIM CYLINDER (NEW)WILL NOT GO ALL THE WAY DOWN

    alpha 1 gen 1 ,bought and installed new trim pump complete, trim cylinders, and new lines, but now my trim cylinders will not go all the way down , tank is full ,goes up and down fine ,just won't go all the way down ,about 2 or 3 inches short any help greatly appreciated ,and which line on...
  9. newtoboat101

    trim sender (starboard) wires

    thank you very much ALLDODGE
  10. newtoboat101

    trim sender (starboard) wires

  11. newtoboat101

    trim sender (starboard) wires

    hello, can someone tell me where the trim sender (starboard) side wires connect to , i have 1988 thompson 240 HT alhpa 1 gen 1, replaced motor and for the life of me can't figure where 2 wires from trim sender connect .Now the trim gauge was wired so i followed wire from gauge back to near trim...
  12. newtoboat101

    1988 thompson 240 color match

    tthanx all , i now see what i'm up against
  13. newtoboat101

    1988 thompson 240 color match

    i wanted to fix some spider cracks ,other areas i have fixed ,tried to match as close as i could, so trial and error would be the only way to match older boats , dingbat,i was hoping that some sort of gel coat super genius scientist would chime in ,and say send me a piece and i can match that...
  14. newtoboat101

    1988 thompson 240 color match

    hello, have a 1988 thompson 240 fisherman ,is there a way to match the color of my boat ,is there a paint chart for thompson boats for my year ,or is there a company out there that could help me match my boats original color? any help appreciated
  15. newtoboat101

    240 THOMPSON BOTTOM DEADRISE

    so i used the angle app on android ,well my boat was not totally level so one side measured 10 degrees and other side read 17 degrees ,should i split the difference and call it 13.5 degrees ,what im trying to figure out is what angle raymarine thru hull real vision 3d ,what do you all think
  16. newtoboat101

    240 THOMPSON BOTTOM DEADRISE

    thanx all, found angle app on phone ,worked great thank you for your help everyone
  17. newtoboat101

    240 THOMPSON BOTTOM DEADRISE

    Hello, would anybody know the deadrise of bottom of boat 1988 thompson 240, looking to put raymarine real vision 3d thru hull transducer,but not sure which one is correct for my application,any help appreciated
  18. newtoboat101

    alpha 1 gen 1 outdrive issue

    lol, last winter took my outdrive off as i do every winter ,got ill,so i amjust getting back to putting outdrive on and its giving me problems,now to your question ,during the winter broke outdrive apart and checked impeller ,didnt look bad at all ,but all ready had taken apart so put new one in...
  19. newtoboat101

    alpha 1 gen 1 outdrive issue

    5.7 vortec /alpha 1 gen1 sei outdrive, i have had outdrive off and back on about 10 times with no issue ,this time had to put new impeller on, no problems there ,but when i put outdrive on ,all went well ,but when i try to shift the cable or shifter will not move from forward position ,,with...
  20. newtoboat101

    need help with hydraulic steering and evoluton EV type 1 pump

    thanx bondo for chiming in with your experience ,appreciate it
Top