Search results

  1. knezzer

    71' Offshore-V 18 - Prize Catch

    got the glass fixed !
  2. knezzer

    71' Offshore-V 18 - Prize Catch

    Dang it. I should have put the steering cable back onto the outboard when it was hanging in the air before I secured it to the transom. Now there is not enough room to feed it through. Anything I can do besides pulling the motor?
  3. knezzer

    What do I have here??

    I've got a 1966 Dart that looked like yours when I got it. I made it into a sweet fishing boat. Nice little boat. I have a 25hp 4stroke on it that suits it well, motor's a bit heavy but with that triple transom knee brace it does fine.
  4. knezzer

    What do I have here??

  5. knezzer

    What do I have here??

  6. knezzer

    Help identifying

    I believe you have a 1969 or 1970 Offshore. I have a 1971 and the bow rails are slightly different and has a different plastic "starcraft" logo on the side. It's pretty much the same as the 18' SuperSport that came out in 1972
  7. knezzer

    Help identifying

  8. knezzer

    71' Offshore-V 18 - Prize Catch

    This also happened. It went really well.
  9. knezzer

    71' Offshore-V 18 - Prize Catch

    Made a bit more progress. I want to use the PVC conduit for some wire. I also want to put my steering cable and or throttle cable in behind the wood side panel. Is it worth trying or should I just run everything up in the gunnel?
  10. knezzer

    71' Offshore-V 18 - Prize Catch

    Howdy folks ! Been a busy summer for me and have finally got around to some progress on project "Prize Catch". Painted the gunnels. Installed the transom. Got a big tube of the 3m5200, that should do it eh? Getting the deck finished so I can start actually putting everything back into place...
  11. knezzer

    71' Offshore-V 18 - Prize Catch

  12. knezzer

    71' Offshore-V 18 - Prize Catch

  13. knezzer

    71' Offshore-V 18 - Prize Catch

  14. knezzer

    71' Offshore-V 18 - Prize Catch

    So I did manage to get the deck installed. I used large flange rivets to attach to the stringers all around edges and screws everywhere else. Also doubled the 5/8 ply for under the seats and the seams where the plywood lines up. As well I sandwiched some leftover aluminum between the plywood...
  15. knezzer

    71' Offshore-V 18 - Prize Catch

    My buddy made these for me. I think the starcraft logo will be nice on my Dart and the other one for the offshore
  16. knezzer

    71' Offshore-V 18 - Prize Catch

    I will be bolting those to together through the knee brace then as well, thanks WM So I've cleaned the inside of the hull again today and laid the rigid foam down. Put the deck back in to mark out where the seats are going. I picked up large flange rivets and smaller rivets so I'm almost...
  17. knezzer

    71' Offshore-V 18 - Prize Catch

    Lots of room to move around in here !
  18. knezzer

    71' Offshore-V 18 - Prize Catch

    I put the new transom in for fun. I still plan on painting it after I drill out some holes. This is how I plan to address the broken knee brace. I saved a few of these aluminum bracket things from a job site. I think two of these JB welded to the brace and bolted through the transom should be...
  19. knezzer

    71' Offshore-V 18 - Prize Catch

    Finally got the frost off ! I have this place to myself for the next 3 weekends so I hope to make some forward progress.
  20. knezzer

    71' Offshore-V 18 - Prize Catch

    We had an early winter freeze ! this pic was taken mid November. The ice was already 30cm or close to 12" on this lake.
Top