Search results

  1. K

    Help please, coil under flywheel wires where do the go?

    I pulled the fly wheel on my 1999 9.9 Yamaha there are two coils under the flywheel one coil has a brown and a blue wire coming off of it and and plugs wright into the blue and brown female clips no problem , However the other coil has 2 green wires coming from it and I see no place to plug...
  2. K

    Belgium 4 hp prop assembly part ?

    I picked up a Belgium made E-rude 4 mod# BE4BRCOB it did not come with a prop, the shaft has a hole forward for the shear pin but no hole aft for a cotter pin to keep prop on the shaft, it looks like there is a groove for some sort of retainer clip to hold prop in place? please help with info...
  3. K

    More confused, more help pls,, 15 UPPER GROMMET

    , Ok so it looks like the water tube upper grommet, changed in 1985 to part # 330426 1984 and earlier is part # 324045 here is my question the 84 looks like the old style grommet that was prone to collapsing and causing blockage problems?? so on these pre 85 motors would you use the newer...
  4. K

    Part # help

    Could anyone help me with the part#s for the upper water tube grommet for a mid 80s Evinrude / Johnson 15 hp. I think the OMC # is 324045 what I'm after is the Sierra & Mallory pn#s Also how do I find them on iboats? thanks much
  5. K

    Good example of Bad, 9.9 / 15 (photo)

    Thought this was a good example of a water pump base plate for a 9.9 / 15 OMC, the photo shows the drive shaft hole very enlarged / worn on the bad one, next to a good one. thought it mite help someone.
  6. K

    1988 Merc 8, carb rebuild problem help

    I just rebuilt the carb on my 8 hp merc, it has the pull choke twist knob deal that pushes on a primer stem on the right side of the carb. my question is about the little rubber cap that fits down over the primer stem, it keeps pooping off when I go to prime the motor what keeps it in place...
  7. K

    re-1935 Evinrude 6011 opposed cylinder " LIVES"

    Thanks for the help on the spark plugs and other things. the link is for a video of its first start.:) 1935 Evinrude outboard - YouTube
  8. K

    1935 sprark plug needed, opposed cylinder 21HP Help with this pls

    I have managed to get spark to the plugs but near as I can figure the autolite 386 that came with the motor seem to fire a weak looking spark, but when I test the spark with a checker it jumps a nice 7/16 to 1/2 inc gap. this is a 1935 evinrude 21 HP opposed cylinder motor 6011. I found a cpl...
  9. K

    Happy thanksgiving all ...!

    :joyous: thanks for all the help, great folks & site God-bless. kodibass
  10. K

    1980 Evinrude 70 (barn fresh)

    Picked this up as a freebee' After I do the basic test compression, spark check, check fuel lines , carbs etc. if it runs well I have read many post about issues with the exhaust port/gaskets on these early models as being a problem causer, so what is the issue in regards to the cover/...
  11. K

    Something bad wrong, please watch video and reply WITH your expert advise..

    First please forgive me for running this post here, I just want to get many takes from skilled folks of all types who may have run into a simalir situation regardless of make. I know none of the history on the motor it was a freebee, P/O stated it runs but there is a hideous noise coming...
  12. K

    My simple pressure tester fot lower units ( photos )

    things needed to build 2 5" section of 3/8 braided fuel hose 1 2" metal tire valve stem 1 Brass T fitting 2 couplers For T to hose connection 1 2" Aluminum bolt & aluminum ny-lock nut 1 3/8 o-ring 4 small hose clamps The aluminum bolt & nut are available at auto parts stores...
  13. K

    70HP no change when plug wire removed, has spark???

    Trying to fix a 1989 E70elcem hooked each plug to a spark plug tester (the kind that looks like a spark plug) all three cylinders jump the gap, but when I start it, I pulled each wire the bottom cylinder changes the engine sound a little, the middle changes the sound allot (motor almost dies)...
  14. K

    1971 18hp fixed ! Success thanks so much!

    I got the re-seal on my old rude 18 done and a successful air pressure test, thanks to all those who helped along the way, I think I am brave enuff now to try it on my 1958 electric start 18hp, this was a test run so to speak. again thanks for your patience and sharing your knowledge &...
  15. K

    No spark, start where?

    my friends Erude would not start for him so he asked me to look at it for him. I said I would' well he brought it by and it was not the boat he had last year he got a new one, this thing is not what I normally tinker with its a E225FPXSRB (2004?) 225 HP Well I did at least pull a plug on...
  16. K

    1971 18hp L/U help (PHOTO)

    I'm getting around to putting this back together and its been so long kinda forget what came out of where, Its a 1971 E-rude 18 SS. bottom of photo is what came out, top of photo is what needs to go in where? I bought the kit shown I think maybe it came with extra's ? like the white nylon...
  17. K

    1971 18HP bearing help which way install numbers up / or down

    OK I managed to get the upper drive shaft bearings out the ones under the upper seal , so here is my question which way do the new bearings go in? one end of the bearing carrier has numbers stamped on it to me seems a bit flatter. the other end has no markings at all, so experts please help...
  18. K

    Needle bearings under Drive shaft seal? 18 hp

    Ok so I got the drive shaft seal under the impeller out & the shift rod seal, So I decided to replace the bearing under the drive shaft seal and have all but destroyed it. So now there is no going back on this decision. Can anyone give me some tips on how to get this stuck bearing (or whats...
  19. K

    Vintage tiller handle (PAT 2926544)

    I have several older E-rudes & jonnys that have the metal tiller extension grip that replaces the plastic stock issue type. these have stamped on them a pat # 2926544 however I have never came across the extension handle or female end so to speak. was wondering if anyone might be able to...
  20. K

    1971 18hp L/U help

    I am trying a reseal on a 1971 18. (mod# 181025-EO55410) I pulled the drive shaft seal out and the needle bearings fell out as well, So are these supposed to just fall out ? Its part# 383829 needle bearing but I cannot tell if they are to be held in as a unit, I could not find any type of cage...
Top