Search results

  1. gregmsr

    Force 125 Slack in Steering

    I searched but not found any posts on this problem that can help me. I have the 125 hp on a 89 Capri. I've got slack getting worse in the steering. The motor will rock side to side slightly while under way causing this "bumping" in the steering wheel. I looked at everything associated with the...
  2. gregmsr

    Pulling to Port

    1989 Force 125, W/Stingray fin. I have to hold the wheel to the right. I let go and the boat turns left most of the time. I can turn hard to the right, and it will straighten up for a little while. It's like getting the motor past half way, then it will go straight for a little while then back...
  3. gregmsr

    Post Guide On's

    Anyone have any pictures of how to mount these posts to the frame? My frame is so far under the boat, the guide on's will not adjust out far enough. I need 25" out to the rub rail from the frame.
  4. gregmsr

    48-50" Guide On's

    I wonder if this length PVC guide ons will be tall enough for a 89 Capri Cuddy? Tall enough meaning, ok the trailer is backed in at the ramp and i'm ready to load. The rear of the trailer is submerged 1.5' which means 30 inches of PVC is above water line. Will the PVC be tall enough to reach the...
  5. gregmsr

    Installing Brake Lines

    On my single axle trailer. Question: Is it necessary to have flexible lines connecting to the calipers? Two flex lines came with the kit (actually three, the one I know where it goes). If I use the flex lines at the calipers, the 72" steel line from wheel to wheel is way too long. I guess I...
  6. gregmsr

    Tachometer Help Needed

    Can anyone help me with finding the proper tachometer for my 1989 Force 125hp O/B motor (1251X9D)? I currently don't have one installed and would like to get one for my 1989 Capri Cuddy. I need the correct tach, where to buy one, and how to install it correctly. Thanks in advance.
  7. gregmsr

    What year motor

    Anyone know for sure what year motor this is? 1251X9D The reason I ask is I ordered a water pump kit for my 1989 Force 125 (ebasicpower.com). Then noticed it was the wrong pump housing that was shipped. They say I ordered the wrong parts and should have taken it apart first and went by the...
  8. gregmsr

    Frank, a PM for you

    I'm stuck! Please check your messages.
  9. gregmsr

    New Prop Question

    I have 1989 Force 125hp. If I get a new prop, what other items must I get with it for installation? Anything like new nut, shims, bushings, ect. I have never changed a prop before. Any help, thanks.
  10. gregmsr

    Step By Step Impeller Change

    I have a 1989 Force 125 (1251X9D), and a Clymer manual. I want to change the impeller myself for the first time. I will study the manual but if anyone has the time, please give me step by step directions on this process. What to look for, potential problems, additional parts that may be...
  11. gregmsr

    Found Hairline Crack in Block

    Last year after buying this 89 Capri w/ Force 125 (1251X9D) I noticed someone had "fixed" the block with JB Weld in the area of bottom cylinder wall on starboard side, about 2"down from head. "CRAP" I said. I didn't notice the fix until a month after the purchase. Well, compression check was...
  12. gregmsr

    All I need is......

    A prop exactly like the one I have now. After looking at the hundreds and thousands of possibilities, i'm lost. Yes, a newbie here. Question: How do I know if I have a "thru hub" exhaust or not? I have a 89 Force 125. I thought the exhaust snout was above the prop on my model. Just a prop like I...
  13. gregmsr

    Force 125 Choke Blowing Fuses

    My Force 125 is blowing fuses when activated. Checked all wiring and saw nothing. Does this mean a new choke? Or maybe a heavier fuse (15amp)? What could cause this? I choked by hand yesterday and went on with no problems.
  14. gregmsr

    Newb Damaged Prop

    Yes I did it, softly ran aground last fall. The prop struck what seemed to be small stones before I could de-throttle, raise and paddle away. Results were slightly boogered up edges and a little paint cracking at the hub but no signs of actually bending. Still looks normal. I filed the edges...
  15. gregmsr

    89 Capri Boat Cover

    Can anyone tell me where the best web-site to buy a new cover? There are many sites but which is best buy? Lowest price? I-Boats, of course! Let me investigate.
  16. gregmsr

    89 Force 125 LU Drain/Fill Plug Gaskets

    Can anyone tell me where I can order these nylon gaskets other than mercruiserparts? They want $19.00 S&H for a $.75 part! Is there any other gasket type I can use safely for these important seals?
  17. gregmsr

    12 volt lighter installation

    Trying to install lighter on 89 Capri. Mounted in dash left of steering wheel in aluminum plate. Hooked up hot and ground wires but keeps blowing fuses. Double checked ground and installed second ground wire with same results. Where the heck can I get good ground? The aluminum plate attaches...
  18. gregmsr

    89 Capri 12 volt Lighter Installation

    I'm trying to install a cigarette lighter / chart light on my 89 Capri but can't seem to ground it enough to keep from blowing fuses. I assume grounding is the problem. I mounted it to the left of the steering wheel in the small aluminum panel. The panel is fastened to the plastic dash with no...
  19. gregmsr

    Bent "Fin?" Below prop Force 125

    On my Force 125 I've noticed the "fin" below the prop (I know there's a name for it but can't remember) is bent slightly to one side (about 1" from exact center). Will this make the boat pull one way or the other and what is the best way to straighten it without breaking or damage? Tried softly...
  20. gregmsr

    Another Lower Unit Question 89 125hp Force

    Ok I changed L/U lube last month just to check it out as I just bought boat. Dropped old lube and refilled, no problem. Put in water a couple more times before winter nap. Yesterday as I was changing lube again I noticed, as I was filling, oil started dripping from the opening just above the...
Top