Search results

  1. R

    Johnson part interchange

    Hello All, Will the recoil starter and cowling from a 97 Johnson 15 Hp fit a 1998 8 Hp Johnson? What happened to the "where used" function on the BRP website? Thanks rcb130
  2. R

    2003 Yamaha/Mercury wiring Harness

    Hi, I have a 2003 mercury 75 Hp four stroke with a Yamaha powerhead. I am trying to wire a standard mercury ignition switch into the engine harness. The engine harness colors are; Black, White, Dark Green, Pink, Brown, Light Green, Dark Blue, and Red. This motor has a ECM for spark control...
  3. R

    2003 mercury wiring harness

    Hi, I have a 2003 mercury 75 Hp four stroke with a Yamaha powerhead. I am trying to wire a standard mercury ignition switch into the engine harness. The engine harness colors are; Black, White, Dark Green, Pink, Brown, Light Green, Dark Blue, and Red. This motor has a ECM for spark control...
  4. R

    How do I wire this?

    I have a 2003 Mercury 75 Hp four stroke motor with carbs. I am trying to wire a new ignition switch that has the following terminals on the switch.M,B,M,C,I,S. Where do the following wires connect? Red,Blk/Yel,Purple,Blk,Yel/Red,Pur/Wht Do I have the correct switch? If not, what is the part...
  5. R

    shift rod length

    I have a 1997 Johnson 40 Hp, Model J40TLEUC. Does anyone know the correct shift rod height and how it is measured? I had the lower unit apart and failed to measure rod before removal. Thanks Rob
  6. R

    any starter experts around?

    Hello, I have a Johnson 2002 55 Hp commercial rope start engine model j55aprlstr. this motor is also known as the Enforcer. I would like to convert it to electric start. Can anyone tell me what starter I need to use or what years will fit and what other parts I would need other than a relay...
  7. R

    question for DHADLEY or any other knowledgeable reader

    I have a 1997 40 Hp Johnson (J40TLEUC) that needs a new pinion and forward gear. My question is this: If the new pinion is the same thickness as the old, do I need to do the driveshaft setup with the special shimming tool? My guess would be that I do not have to. Also, is there an easy way to...
  8. R

    Lower unit interchange

    Hello All, I have a 2003 55Hp commercial rope start engine that needs the lower unit replaced. Does anyone out there know what different lower units will fit? Drive shaft is .75 dia and 17 tooth spline. Thanks in advance for the help Rob
  9. R

    Interchange help

    I have a 2003 J55APRL which is basically a rope start 55Hp 20" commercial motor with a durajet propulsor that I bought at auction. Upon starting the motor it promptly spun the upper drive shaft bearing in the gear case. This was due to the fact that it had no water pump in place. My question is...
  10. R

    55Hp Evinrude twin misses at all speeds

    Hello to all, I have a 1994 Evinrude commercial 55 hp twin that misses thru the entire operating range. It starts easily but misses. I have changed out the ignition coils, power pack, spark plugs, changed plug wires, disassembled and rebuilt carbs, new fuel filter and went thru the sync...
  11. R

    Carb identification

    Hello, I came across 2 carbs in a junk box I bought and am having trouble identifying them as to model year and engine. They have the following numbers cast into the body (none of which the BRP site recongnizes) : 335830-CU (one has 335830-BU) 327889 334327 They both have 1 3/16 cast...
  12. R

    Can anyone identify this wiring?

    I have a 1999 OMC 70 Hp engine with model #J70PLEEE,engine family #X1PXM0056210. This motor is set up for the OMC systems check wiring. However, at the rear of the motor below the spark plugs is the typical large round red amphenol type connector used on earlier models of evinrudes and johnson...
  13. R

    Source for Amphenol Pins

    I am looking for a source for the pins in the large red connector on the engine side of the wiring harness. I have been all over the BRP site and cannot find part numbers for these pins. There are different size pins so there has to be more than one number. Can anyone supply part numbers or a...
  14. R

    Evinrude/Johnson Red Connector

    Hello, Can anyone provide an Amphenol part number and source for the large red connector in the wiring harness? I have one that has several pins corroded off at wire junction. Thanks in advance for the help. Rcb130
  15. R

    How to deciper Engine Family

    I have a 1999 Johnson with engine family X1PXM0056210. what does all this decode to mean? thanks Rob
  16. R

    Motor year ID

    Hi, I have a couple of questions. Can anyone identify the following motor? It is a 40 Hp Evinrude. Sn G03003019, Model E40EENM. Second question: I have obtained two 35 Hp I-MARS motors. These can be submerged to 400 feet and brought back up and restarted. These are pump jet motors, they are...
  17. R

    water leak at lower unit

    I have just rebuilt a 1981 Rude V6 150hp, Serial No. J0001034, Model E150TRXC1H. Upon startup on muffs, I noticed a lot of water leaking from the joint of the lower unit and the exhaust housing and then after a few minutes also from the vicinity of the top of the exhaust housing. Is this to be...
  18. R

    Installing Cageless Bearings

    Is there a preferred method of installing cageless bearings? If yes, please indicate the steps, any type of orientation and any cautions.<br />Thanks<br />Rob
  19. R

    what year is this gearcase?

    I am helping a friend with a 1981 evinrude v6 rebuild. The lower unit is definetly not the original. Is there a way of dating the gearcase?<br />Thanks<br />Rob
  20. R

    second request for help on this

    I am helping a friend repair a 1981 rude v6. I am stumped by the following problem. When I first disassembled the lower unit to replace water pump and do a reseal on the gearcase I notice the driveshaft would only do a quarter turn. Once the pump was off, it rotated freely. I put the new pump...
Top