Search results

  1. W

    Proper trim for my 1570 Landau with 15hp Mariner

    Pictures of current setting for the trim. Any Thoughts as to proper positioning? I have moved the pin setting to the lower(1st hole). Seems to me if I move to higher hole or setting the problem would worsen. Webekin
  2. W

    Stuck float ??

    Started a new tread regarding cavitation issues. Webekin
  3. W

    Stuck float ??

    I have the owners manual, 32:1 breakin, then 50:1 there after. Need guidance on the proper positioning of the lower, I will get a picture to verify that the leg is long enough for the boat. Webekin
  4. W

    Stuck float ??

    Addded another gallon of fuel mixed 50:1, removed the filter cleaned a small amount of black Crud, added some seafoam! Started on the 1st pull, idled ran all the way to the south end of the lake. One thing, seems to rev when I accelerate any above less than half throttle. Like it is hitting an...
  5. W

    Stuck float ??

    Ran great last Feb. when I purchased it. The filter looks clean. The impeller was inspected last Feb. Ok. Thanks, I'll check on these items. Webekin
  6. W

    Stuck float ??

    Maiden voyage of the 14 foot Landau with 15hp Mariner, choked it pulled 3 times fired , died. Never fired again, wore a large blister on my pulling finger. After using the trolling motor to catch bait, son says "think the float could be stuck" so tapped the carb bowl and it fired up, ran, idled...
  7. W

    Transom bent on my 14' Landau

    Ok. I'll look I to the plywood!
  8. W

    Transom bent on my 14' Landau

  9. W

    1978 Evinrude, 35 HP starter will not spin the fly wheel

    Yes, it will spin the '82 with both plugs in. We will be cleaning the exhaust today. Webekin
  10. W

    Ted Williams idling bad drive shaft

    Yes, I have it apart and the splines on the drive shaft are Wopped up. I have worked them over with a file and dremmel. The drive shaft will will fit the clutch now, and I have it all back together, ready to test the clutch/drive shaft splines fitment. Then the post side transom mount broke, I...
  11. W

    1978 Evinrude, 35 HP starter will not spin the fly wheel

    So my grandson and I are working on a 35hp Evinrude made in 1978. It will not spin up, I removed and cleaned and polished the starter components, to encourage it to work properly. Still not spinning up. Removed a starter from my 1982 Johnson 35HP and same issue will not spin, engages but fails...
  12. W

    Ted Williams idling bad drive shaft

    So I have the lower off the unit. Have removed the(6) bolts and nuts that fasten the mid section to the power head, it is loose but will not separate. Has a gap, al away around, will wobblee up and down, back and forth. but will not separate. What have I over looked? Want to have look at the...
  13. W

    What is the function of the orifice plug

    Sure enough, my helper installed the nozzle gasket yesterday, and we put it into a tub of water today, and it started on the 3rd pull. Ran nice, idled down, and died then restarted on 2 pulls. accelerates nicely, and then idles back well. thanks for the tip on the nozzle gasket. I was sure it...
  14. W

    New Johnson J35EL CND

    Was just removed from the charger. Webekin
  15. W

    What is the function of the orifice plug

    So back to the JWF 22, the carb. Kit has been installed, and it will start, if the throttle is almost full, but it runs as if it is to rich. So reduced the fuel flow at the shutoff valve, to the point of shutting off fuel. At this point it began to increase in RPM's, ran great until it ran out...
  16. W

    New Johnson J35EL CND

    We will use an analog next time! Webekin
  17. W

    New Johnson J35EL CND

    We checked the battery, it was 14.5. I can check the others today. Using the newer battery from my 1992 1\2 ton Chevy truck. Webekin
  18. W

    New Johnson J35EL CND

    Yes!
  19. W

    New Johnson J35EL CND

    Ok, Grandson came over and we worked on the motor. We connected a battery to the power supply and the starter motor does not spin up fully. As in it tries to, engages the bendix?, the gear that engages the fly wheel, but the FW does not turn. The gear is slow to drop back in the non use area...
  20. W

    Ted Williams idling bad drive shaft

    Missing some of the number, 217-59x30! Webekin
Top