Search results

  1. P

    05' Tohatsu 15 4 stroke. Starts and dies within seconds.

    Hi pvanv, maybe my problem is similar. I have an NSF 15C 2009 4 stroke. IS it possible that oil too full could be my problem? Or when I lifted it with my cherry picker if I tilted it the wrong way, would that prevent starting? Thanks, Nick
  2. P

    NSF 15C 2009 Still won't start

    The latest development is that I tested the spark plug spark and it jumps 8mm no problem. So now I'm back to the carburetor. I've had it apart twice and cleaned it thoroughly. I've disconnected the incoming fuel line and see fuel flowing when the motor is turned over. I've unscrewed the plug...
  3. P

    Tried everything, except what's really wrong.

    Motor is 15 hp Nissan Marine 2009. Electric start.
  4. P

    Tried everything, except what's really wrong.

    I tested spark plugs, thought they were weak. Replaced after setting gap. Use multi meter with peak voltage adapter. Seem to indicate magneto was bad so I replaced that. Tested kill switch and it was fine tested neutral safety switch and it was fine. After following tests from the tehach to...
  5. P

    Tried everything, except what's really wrong.

    NSF 15C, 2010 MODEL, won't start. Replace magneto, pulser coil, ignition coil cleaned carburetor twice, installed new plugs tested kill switch and neutral switch. This thing won't start. I've also tested peak voltage, but that's irrelevant because I've replaced all the parts. The CDI i...
  6. P

    NSF 15C No Spark.

    Hello, So that ignition coil would not be the problem? It would be the CDI or the charge coil under the flywheel? I do have a very week spark.
  7. P

    NSF 15C No Spark.

    Thanks a bunch Sea rider.
  8. P

    NSF 15C No Spark.

    The latest is that i found that both plugs have a spark but it's weak in my opinion. Im currently tracking down a DV adapter to test some components. I'd like to know the specs to test resistance but can't track them down.
  9. P

    NSF 15C No Spark.

    Hi, This is my coil, I'm calling the ignition coil but maybe I'm wrong. It only has two wires coming into it and the spark plug wire is going out of it. Does this have a primary and secondary winding? Another curiosity is one coil that goes to two spark plugs. Maybe I didn't properly test this.
  10. P

    NSF 15C No Spark.

    Hi km, I did bypass the safety switch and it has a neutral safety switch, it has an electric start. No spark is my problem, was hoping I found the problem with an inexpensive part.
  11. P

    NSF 15C No Spark.

    This is the pulser coil and when measuring across the two wires it's at 202 ohms when in that mode on my multi tester and when testing continuity it reads nothing. I'm assuming this is a bad Pulser Coil? Could tis be the reason I have no spark? Thanks Nick
  12. P

    NSF 15C No Spark.

    Would anyone know the resistance for the Pulse Coil? Can't find the spec anywhere. I think the ignition coil is fine, I checked the safety lanyard and the neutral safety switch, all good. My current reading is about 194 ohms for the pulser coil. Thanks Nick
  13. P

    No spark on 2009 15hp ouboard

    Trying to diagnose the no spark. I can't track down the resistance reading I should have on the Pulser Coil. I think my ignition coil is good, have not tested the stator yet. What should the resistance be?
  14. P

    Leak or no leak?

    I have this 72 OMC 225hp, trying to fix a leak or perhaps it's meant to shoot water out of this location? It's doing the same thing on the port side. Before this it had black RTV or something smeared all over the seams. I took it apart, cleaned the surfaces, replaced with a new gasket, O ring...
  15. P

    Nothing to starter

    Thanks a bunch. I'm working on it now.
  16. P

    Nothing to starter

    Ok, I'll try that. I noticed in the manual on the electrical diagram, there's a assistant relay to the starter relay I think that's what it said. Why would I need a relay to the starter relay?
  17. P

    Nothing to starter

    Are you saying measure voltage at solenoid when i turn the key? There's no sound of solenoid clicking. I do get a weird buzzing sound up by the dash.
  18. P

    Nothing to starter

    Hello, I'm taking a break from a tilt trim motor problem. This is my new problem. 1972 OMC TUFM-21C. 225 Outdrive. That's it, that's my problem, i have this boat in the first place. Just kidding. When I turn the key nothing but a buzz sound, like a speaker. I get no click, like a bad...
  19. P

    1972 OMC 225 Tilt not working

    Could it also be the relay that's clicking. A bad relay?
  20. P

    1972 OMC 225 Tilt not working

    Hi Kenny, Yes it's a Fiberform made across the border from me in Spokane Wa. It's in great shape. I bought it from a person that had it stored for a couple of years but properly winterized.
Top