Search results

  1. Jack Daniels

    FORCE 1983 85 HP lower unit question

    Ok so i resealed the lower unit and changed the impellar with relatively good sucess. However, since i had a shift linkage screw issue, i wanted to bump the motor in gear to make sure it worked correctly. I did this on muffs and it went into gear but there was slight gear noise from the lower...
  2. Jack Daniels

    Bolt stuck in prop

    After resealing my lower unit, i noticed that behind the prop one of the screws from the lower unit got lodged in between the prop wall and the hub. I cant seem to get it out and was curious if i should take it to a prop shop and have it removed. What issues can arise if i leave it there, it...
  3. Jack Daniels

    Resealing Lower unit

    Ok i have a 1983 FORCE 85 hp out board, i had milkey gear case oil during last winterization. I purchased the reseal kit for the lower unit, my question is, has anyone done this before and if so how hard of a task is it. I have a new impellar to put in so i have to drop the whole unit anyway...
  4. Jack Daniels

    RPMs?

    Ok since i have a newly installed tach i took the boat out the other day and reached 6k rpms. From what i understand for my 1983 85 HP FORCE; 5500 is the max rpm you should run. My tach is a 6000 RPM tach which should be suffiecent, but on to my question. When i ran her the other day at WOT...
  5. Jack Daniels

    Bilge pump Install question

    My bayliner currently does not have a bildge pump in the bilge area, i have one in the boat but i have to place it and pump mannually. Its only a 16ft boat do you think plumming a permanent pump is worth while and if so where should i install the exit hole. I would ahve to drill a hole for the...
  6. Jack Daniels

    Pitot Tube Speedo

    Is it uncommon for the speedo not to work until you get to WoT. Mine wont work until im at higher speeds. Do you think i have an obstruction in the line or a faulty speedo, or is this just normal? Thanks Guys
  7. Jack Daniels

    Transducer Mounting position

    Ok i have seen other threads on this subject but wanted to get your opinions anyway. I have my transducer mounted below the hull, so its probably 2 inches below so to speak. I cant get it to read at WoT and am under the impression that i have it mounted to low. What do you think, should the...
  8. Jack Daniels

    Power head switch

    Will a 1986 FORCE 85 hp power head fit on my 1983 FORCE unit? Thanks
  9. Jack Daniels

    Battery Drains

    Hey all, quick question. I just bought a new battery from Mier and am currently having issues with it losing charge. Its the main starting battery for my outboard, in addtiion to starting, i run the depth finder and basic radio off it. Do you think the Depth finder and deck radio is causing...
  10. Jack Daniels

    Rebuilt FORCE Powerhead

    Ok guys, just bought a completely rebuilt FORCE powerhead. It was over bored, new pistons and rings, new bearings, and new carb. I bought it on ebay for 250 bucks, can you believe it what a steal. Anyway, I only purchased it becuase i know eventually i will need it but the one i am using now...
  11. Jack Daniels

    Tach Install

    Ok so i finally have my 20 pole tach and want to figure out how to install it. I think its relatively easy, so my question is, what do i hook up the signal source pin on the tach. Didtn come with great directions per my motor. BTW i have a 1983 FORCE outboard. I attached a figure of the tach...
  12. Jack Daniels

    1983 FORCE Tach option

    Hey guys I am looking to add a tach to my FORCE 83 outboard. Do you guys have any recomendations that would be easy to install and what type do i need to use? Thanks
  13. Jack Daniels

    Starting Outboard Question

    Ok since i know that this forum has some trouble shooting studs, I will bring this dilema to you guys and see if you know the answer. Ok I have a 83 FORCE outboard that has an intermitant starting issue. The problem is sometimes when i turn the key it does nothing, when i mean nothing, i mean...
  14. Jack Daniels

    Part needed for fish finder

    Hey guys wondering if you can help me. I resently purchased a new fish finder and lost a part. I think one of my wifes cats thought it was a toy and ran off with it. Well anyway, im looking for the plastic cover that covers the hole above the water line in the transom where the transducer...
  15. Jack Daniels

    Compression on a Powerhead

    Is it possible to check the compression on a powerhead without having the ignition system installed, the powerhead connected to the outboard, and the flywheel disconnected. I just bought a new powerhead and want to know if i need to rebuild it prior to starting the process. Thanks
  16. Jack Daniels

    NooB help?

    Ok so im going to replace my water pump on my 1983 85 HP FORCE outboard and was looking on iboats for the correct kit. It has me completely comfused, its also called the impellar do i need to just replace it or is there a whole kit that i have to get. Also do you guys recomend a fuel pump...
  17. Jack Daniels

    1984 FORCE 85 HP Powerhead

    I just bought one on ebay for really inexpensive and am planning on rebuilding it. My question is i have a 1983 powerhead on my FORCE outboard and want to make sure they are interchangable. I only paid 50 bucks for it so it was a find and i assume that since its only a year off that its...
  18. Jack Daniels

    Saturated Foam???

    Whats the easiest way to tell if my foam is saturated? I have an 83 Bayliner and people have told me to check if the foam is saturated. From what i understand its never been uncovered when outside and its been shrink wrapped every winter. The rear deck has been replaced professionally due to...
  19. Jack Daniels

    updating an outboard motor

    Hey guys wanted to ask a question regarding updating the appearance of a 1983 outboard. Currently its a white FORCE 85 HP and it seems like the paint is in decent shape. However, I am not a big fan of white anything and was wondering what steps i should take to repaint in black. Can i just...
  20. Jack Daniels

    1983 FORCE 85 HP, honey do list.

    Ok so you all know by now that i have low compression, approximately 85 on all three cylinders. So i am writing this to present my to do list during the winter in hopes of getting this bad boy to run as long as possible. 1) Decarb the engine using appropriate methods-- I heard that this can...
Top