Search results

  1. O

    engine removal

    Taking my 200 h.p. 1989 yamaha to replace power trim motor, I have an engine hoist and I'm just wandering are there any pointers or steps in doing this, as far as taking the engine off safely. Also do I need to disconnect my cables, I have a foot or so of play and I need to just get to the...
  2. O

    yamaha motor change

    I currently have twin1989 200 h.p. yamahas and may be looking for newer power.Does anybody know up to what year engine I can purchase and still use my outboard rigging,controls,cables,oil pump-tank,plugs,gauges, connections,ect.Looking to install basically two motors on my transom.
  3. O

    power trim replacement 1989 200h.p.yamaha

    Looking to replace either power trim motor or try to locate entire assembly depending on whether motor comes out without impossible corrosion issues.Worst case senario how bad of a job is it ?Where can I find power trim assembly?Approximate cost?Specific possible obstacles?Looking for general...
  4. O

    1989 200h.p. trim motor

    I have a 1989 200h.p. yamaha the trim motor works intermittently , I can initiate the running by gently tapping on trim cover.The motor sounds a little weak when engaged.Assuming corrosion inside or brushes starting to go.Question, can brushes be replaced or does trim motor assembly have to be...
  5. O

    yamaha power trim

    1989 200 h.p. yamaha with only a click in the trim motor , the trim works intermittently less often than not. Can the top of the trim motor be opened with the possible intention to replace any parts, the trim motor sounds strong when it engages.
  6. O

    oil pump replacement

    I have to replace my main hull oil tank pump on my 1989 200h.p yamaha, and it appears to have alot of corrosion including the locking screws.Are there any tricks of the trade to get this out without damaging the plastic oil tank,there is a possibility I may have drill the screws.Also if the...
  7. O

    precicision blend issue

    1989 200h .p. yamaha This is a continuation of a unresolved problem.Specifically, the engine mounted oil tank is not getting any oil.The pump does not turn on when key switch is turned on.My volt meter shows 12 volts going to main tank sensor however no voltage is going to the pump when the key...
  8. O

    lower unit leak

    After changing lower unit oil and looking at old oil, it appears there is a water contamination.Question, what possible seal areas could be suspect?Although it appears to be a slight leak over the past season what possible damage could result if left unaddressed?
  9. O

    shift cable adjustment

    Im replacing my 200h.p.1989 yamaha shift and throttle cables. I set the end fittings to the same thread count as before,the forward shift movement feels stiff and the throttle engages quickly ,the engine setting appears good my question is if I adjust the shift setting on my 704 binnacle...
  10. O

    water tube from water pump 1989 200h.p. yamaha

    While taking off lower unit to change water pump, the copper tube broke off about 2 inches inside the mid section portion of the lower unit.Question if I simply push the broken section into the mid section of the lower unit,what is the chance the water will travel mostly into the tube to the...
  11. O

    shift cable and lower unit question

    Im in the process of replacing my shift cable on my 200h.p 1989 yamaha.While making some adjustments at the motor I noticed the shifting spline goes into gear easier when slowly moving the propellor, is this normal? Generally when shifting into gear at the throttle it feels a little stiff.Also...
  12. O

    1989 200h.p. yamaha oil injection problem

    The alarms work and main tank transfer pump works when bypassed directly to battery.The manual oil toggle does not.The led gauge flashes only once before setting on green.The other led flashes 4 times before setting and that system works.Question does the gauge only display information inputted...
  13. O

    standard horizon 160c gps

    Had battery charger on,gps on, turned over engine and must of shorted out gps.On and Off switch doesnt work, gps stays on with just a lit blank screen.Question :any inline fuses or fuse inside unit that can be replaced?Also is there a reset button if so where?Any help appreciated!! Problem...
  14. O

    stanadard horizon 160c gps Oddysea1

    Had battery charger on, gps on , and started engine must of shorted gps out. When battery switch goes on ,gps turns on to a blank lit screen.On and off switch doesnt work. Any idears on inline fuses on wire or inside unit itself before sending out?
  15. O

    oil injection problem 1989 200h.p yamaha oddysea1

    This problem started out on a intermittent basis over several months. The led gauge would flash several times while the engine was running ,ocassionally low oil alarm would go off.Now when turning over motor the led arrows flash only once and sets on green light vs other working motor which...
  16. O

    electrical/starter problem 200h.p 1989 yamaha

    The starter is not getting any power to it.It is an new cond. The solenoid has been checked along with battery and terminals,along with power head in line fuse.The electric choke works along with gauges when key is on position.When turning key to start no draw is detected by volt gauge. As of...
View older results
Top