Search results

  1. fishdog4449

    19' grady white power options

    Hey how are yall doin? I have quite a few motors sitting around so I've been looking for a larger boat/trailer combo without a motor. I found a 1976 Grady White 19' in good shape with a 2000 trailer...The ad says cabin cruiser but if it's a 19 then most likely a cuddy. I'm going to look at it...
  2. fishdog4449

    aahh to have more garage space!!

    http://richmond.craigslist.org/boa/833324645.html :)
  3. fishdog4449

    Glassmaster transom damage

    hey guys 1981 Glassmaster 18' runabout '76 115 tower of power While I was inspected trim cylinders after the lake yesterday, I noticed there was a slightly large problem with the lower starboard motor bracket, which seemed to have made its way into the transom. Obviously, the wood is rotted...
  4. fishdog4449

    Mercury 1150 tachometer settings

    Hey guys love this forum two quick questions here '76Merc1150 My new teleflex tach came in today and wondering if I should connect the sender wire from the plug on the front of the control box the controls (switchbox) or from the stator wires (alternator)? Pole setting should be 6P right...
  5. fishdog4449

    starting and water problems 72 evinrude 100

    Ok so I dropped the LU last week to rebuild the water pump because the motor wasn't circulating water. well the impeller looked brand new, the vanes hadn't even set yet. Well I put the new one in anyway and put LU back on. Tried to start it and it would fire and start, but slowly die. Or start...
  6. fishdog4449

    building swim platform?

    Hey guys I've been wanting to add a small swim platform on the stern of my glassmaster (port side). I've been looking on ebay and it seems that the little premade ones with teak or plastic or whatever run 80-150$. seems a little much. I'm considering making one with some angle brackets and wood...
  7. fishdog4449

    1972 Evinrude thermostat questions

    The manual says that to replace the t-stat you have to remove the powerhead? Doesn't seem right. Is there an easier way to do it? Also on this motor is there a way to back flush the cooling system with the lu removed? On the starboard bank of cylinders, on the outside, there is a threaded plug...
  8. fishdog4449

    stripped bolt removal (72 Evinrude)

    Hey guys, I'm kinda at my wits end with this one. The trip tab bolt is VERY rounded none of the sockets even fit it let even if I had one that did there are no edges to grip. Closests socket is 3/8s, but it slips. Have tried heat and penetrating bolt buster too. I'm sure that if I could get a...
  9. fishdog4449

    Schooner sailing trip with pictures

    Thought I would share a few pics with you guys from my recent sailing trip aboard the Schooner Virginia. She's a twin masted pilot schooner about 130 feet in length. Two other cadets and myself from our MCJROTC program at school received scholarships to spend a week of sail training on the...
  10. fishdog4449

    Mercury 1150 hard shifting question

    Hey guys two quick questions here (1976 merc 1150) 1) Is there a way to make the throttle/shift handle easier to move? Couldn't find any adjustments on the controls. It takes alot to muscle it into gear, but once it's in gear the throttle moves fine. (not an engine problem, have disconnected...
  11. fishdog4449

    Mercury 1150 running hot? (updated, with pics)

    Hey guys, Took the '76 115 out on the lake today for the first time. it ran great, started on the first try had plenty of power. However, after running for a while the telltale water and water spitting out of relief ports was hot. Not scalding hot, but quite a bit hotter than lukewarm. Impeller...
  12. fishdog4449

    '92 F150 vibrations/drive train problems

    Hey guys, question about my truck here..1992 F150 manual 5spd 4.9L I6. Driving at 35-50 mph there the whole truck begins to vibrate...almost sounds like that helicopter sound you get with one window halfway down, except you feel it in the floor and seats as well. Once you get above 50 it goes...
  13. fishdog4449

    1972 evinrude v4 restoring

    Hey guys, Finally got the ol Evinrude running perfectly and got her nice an tuned up. Now for a cosmetic restoration and a few new wires and new fuel pump then my friend will be using her on a lake/bay boat. I'm not really sure I like the paint/decal scheme for 1972, so I am considering making...
  14. fishdog4449

    evinrude 100 electrical issue

    got the motor for free from a friend,said it ran, but a diode(thats what he called it, not really sure what it is) in the control box gets hot and starts smoking. not good. I didn't try to start it, but oiled the cylinders and tried to turn it over. it turns over slowly and the starter gets...
  15. fishdog4449

    evinrude 100 freebie

    Hey guys heres some pics of my newest freebie. 1972 Evinrude 100 v-4. Friend wanted it out of their yard, it actually runs well and has plenty of power, but has one issue with ignition. (will make seperate post on this). Motor was run in freshwater only and well taken care of. Also got two...
  16. fishdog4449

    Mercury 1150 rectifier test

    Hey guys, quick question here. Whats the best way to test the rectifier (1974 Mercury 1150) Should be able to just measure voltage at battery cables while engine is running right? thanks i love this site!!
  17. fishdog4449

    '74 Mercury 1150 reed cages yamabond repair

    Hey guys! Yet another question for all you Merc Gurus! While I have the beast on the workbench with powerhead off, I want to make sure everything on the motor is in great condition. The motor ran before, but as you may have seen from my other post, she was gettin a little water in number 3 so...
  18. fishdog4449

    Mercury 1150 powerhead removal question

    Hey guys! 1974 Merc 1150 Removed 8 bolts that hold the powerhead on as well as the shift linkage, and she wouldn't budge. what else do I have to remove to remove the powerhead?? Is is necessary to "break' it free or something like that with a mallet? I also dropped the lower unit so that the...
  19. fishdog4449

    Mercury 1150 powerhead weight?

    Anyone know the approx. weight of 1974 merc 1150 powerhead? Pulling it to replace exhaust gaskets and need to know for lifting purposes. Thanks guys!
  20. fishdog4449

    mercury 1150 flywheel bolts thread pattern?

    Anyone know the thread pattern for the eight bolts clustered around the inner part of the flywheel? (1974 Mercury 1150) Thanks!
Top