Search results

  1. W

    prop question

    i have a 9.5 evinrude that has trouble getting on plane i had a michigan 012008 prop on it i have 2 others that i have not tryed yet i dont know alot about props or the #s on them so i will tell you the other 2 i have and maybe some 1 can help me out the other prop is smaller <br />8x7 387334...
  2. W

    engine noise but runs well

    i have a 1972 evinrude 9.5 that rattles at idle but runs well. i can seem to find the rattle checked everything i could think of.like i said it does not have a miss or anything and seems to go away just off idle.
  3. W

    moveing motor up on transom?

    i have a 9.5 in an aluminum 12 foot vhull the cavatation plate is alittle low and i am having trouble getting on plane.can i move the engine up about an inch and place a peice of solid rubber between the bottom of the engine mount and top of the transom?this will almost put my cavitaion plate at...
  4. W

    9.5 on muffs ? can it be done.9.5 evinrude owners help

    i am sick of filling a barrel and running my engine before leaving for the river then when i get home filling it again to fluch the engine. but i cant seem to get the muffs to fit on my small 9.5 evinrude is there diffrent sizes or a trick ?
  5. W

    HYDROFOIL for small outboard ?

    i am looking for a hydrofoil for a 9.5 evinrude all the 1ns i have seen are pretty big. does any1 use them on small motors if so how do they work
  6. W

    boat wont plane

    i have a 12 foot vhull aluminum aero-craft with a 9 1/2 evinrude on it.i just took it out today first time and could not get it to plane.engine runs great i have been though almost every bolt on it.there is some adjustments on the engine tilt but i am not sure how much to tilt it.i am not really...
  7. W

    what is the best way to load a boat?

    i am wondering if it is better to power load or to winch the boat on the trailer?
  8. W

    jet drive for a 9.5 evinrude???

    i am lookin to do something a little diffrent do they make a jet drive for a 9.5 ? if so where and how do i locate 1? anyhelp will help thanks
  9. W

    thermostat bolt stuck

    i am trying to remove a stuck thermostat bolt i dont have any problems with over heating i just wanted to check if there was a thermostat in the used engine that i got.should i take the chance of breaking it off or just leave it alone and dont worry about it ?
  10. W

    trying to find a lanyard kill switch for a 9.5 evinrude

    this is what i found but i can find who sells it <br />AP2888 Lanyard replaces OMC #432230 i want to replace the push button with a lanyard kill switch but dont really want to drill out the hole i would like a direct replacment if i can find 1
  11. W

    COWLING COVER SEAL

    what are you guys using for the cowling cover seal i have an evinrude and the seal is all cracked and falling apart
  12. W

    fuel bulb size ??

    i ahve a 9.5 evinrude and i am running a 5/16 bulb and fuel line in it is this too big for this engine ? its what it came with (used)but i have problems cold starting the engine and i have changed everything esle but this
  13. W

    adjusting points on a 9.5 evinrude

    my question is where should the tiller arm throttle be set when adjusting the points ? i see that when you move the tiller arm the point plate turns and messes up the gap ? does it matter where you set it as long as you are at the top of the lobe on the cam?also does it matter what plug wire...
  14. W

    evinrude 9.5 year?

    model 9622 a <br />serial e01337<br />can any1 help thanks
  15. W

    where to get 6 gauge wire ?

    i am lookin for about 18 foot of 6 gauge wire i would like the pos and neg to be in a shrink wrap protector.or at least connected together. i cant find this anywhere.its for my trolling motor can anyone help me ???
  16. W

    hard starting 9.5 when cold

    i have an evnrude 9.5 thats hard to start (10 pulls)when cold 1ns it warms up it starts well (2 pulls)but has a miss.i took the flywheel off and found that the point assembly plate was wore out and had a ton of play in it.when i moved the plate side to side i could see the point gap changing and...
  17. W

    plug wires and gaping 9.5 evinrude

    ok here is the problem the engine was a very hard to start and had a miss.i took the flywheel off and found that i had a lot of play in the plate that the points bolt to.so much play that when i would move the plate with the tiller arm i seen that the points where changing gap.i have a doner...
  18. W

    how much weight is too much ?

    the boat is a 12 foot aluminum vhull rated for 661 lbs.is that total weight including motor and fuel ? i have a 9.5 evinrude (60 lbs) 6 gallons of fuel (50lbs) a trolling motor (30 lbs) battery (45 lbs) me 200lbs and a freind 170lbs thats a total of 550 with out cooler and other little items...
  19. W

    pisser on an 50 hp evinrude

    i dont know where the water is supose to be pissing from on this engine.i run the engine for 20 min and the head stays warm to touch but not hot.i see that is pisses water out under the water line but i dont know if it is supose to be comming out somewhere else on this model its a 1974 50 hp...
  20. W

    run time on 2 gallon tank 9.5 evinrude

    i am wondering how much run time i can get on 2 gallons of fuel i have a 9.5 evinrude.on a 12 foot aluminum vhull. i know i cant get an exact time but somthing close would help
Top