Search results

  1. A

    power tilt/trim 1982 johnson 90hp v-4

    my tilt/trim on my johnson has started to slow down significantly. It is going down slowly and not coming up without a little help. Any suggestions on what to do with it. I have the OMC service manual but I was hoping to get some input from someone on here with experience. Any help is greatly...
  2. A

    1982 johnson 90hp v4 ignition coils

    i am almost finished re-biulding my 90hp johnson and have relaced all of my fuel lines and now I amm checking spark on all of the coils. I am only getting spark on two out of the four. One wire was bad so that ruled out a faulty coil but the other I cant get spark on. I am going to go ahead and...
  3. A

    1983 johnson v4 90hp compression

    anyone know what compression should be on a 90hp crossflow johnson? it is a 1983 year model. any help is appreciated.
  4. A

    johnson lower unit oil replacement

    I have a 1982 johnson 90hp that I drained the lower unit oil and replaced the water pump. I just need to make sure of how to put it back in. Any help with the procedure would be great. And what kind of oil should I use.
  5. A

    1982 90hp johnson, need fuel line diagram

    i re-built my 90hp johnson v4 and in my manual there is a diagram for the vaccum hoses that go to the intake manifold and the carbs but i can't find a diagram for fuel lines that go from the fuel filter to the carbs and the line that goes from the fuel line in to the fuel pump. there are quite a...
  6. A

    90hp johnson blown head gasket

    i bought a boat/motor from a friend. he blew the head gaskets on both cylinders. he replaced them and flushed the motor out thoroughly and didn't run it for 2 years. I broke it loose and have re-built it for the most part. i replaced the thermostats and took the water distribution plates off the...
  7. A

    1986 Mercury 150hp BlackMax overheating??

    I helped a friend change out his impeller on his 150 because he said it was peeing intermitently and overheating. Evidently the past two or three trips out the alarm has gone off and it is loosing power. He said the pee hole in the back wasn't peeing as much as it should. He replaced both...
  8. A

    johnson compression question

    i have a 1983 90hp johnson that I am re-building and have gotten some help from you guys and i have another question for you. I am just about to bring her back to life and want to know what my compression should be on the cylinders.
  9. A

    90hp Johnson manifold gasket question

    I am re-building my 1983 90hp Johnson v-4 and am at the front of the motor. What I need to know is if someone knows whether or not there should be a gasket in between the carbs and the metal plate that mounts to them that is the airbox. And if anyone knows where I can get a diagram for the...
  10. A

    Johnson , Year and Hp???

    I have the model number and serial number of a little johnson outboard that I need help finding out the year and hp. <br />Model# CD-25R<br />Serial# J2910327<br />Thanks!
  11. A

    1983 90hp Johnson compression

    I am re-building my 90hp johnson that was seized and am at a crossroad in the compression department. I un-seazed the motor and cleaned out the cylinders and put on all new head gaskets, intake gaskets, exhaust gaskets and reed gaskets. I have not put the carbs back on yet but tried to check...
  12. A

    1983 90hp Johnson fuel pump

    I am in need of a fuel pump for my 90hp johnson. I was removing the fuel line from it and the nipple that the line attaches to broke off! Does anyone know where I can get this part or a whole pump fro less than $50 at the dealer?? Trying to save some money on this rebuild. Any sites that are...
  13. A

    parts for 1960's evinrudes????

    Anyone know where I can get parts for a 1968 evinrude outboard. I specificaly need a hood.
  14. A

    1968 5hp Johnson

    I aquired this motor for my jonboat and need a hood for it, does anyone know where I might have a chance finding a hood for it. I have looked for one on ebay but no luck and the dealer says it is discontinued. If there is a model or a diferant year that will fit it I think that would work...
  15. A

    evinrude and johnson year

    i am looking at some outboards on ebay and need some help finding out what year these are.<br />4hp johnson/Serial#E4150385 Model#4W75A<br />5hp johnson/Serial#J2523159 Model#LD-10S<br />?hp evinrude/Serial#E07470 Model#9022C<br /><br />Any help is appreciated!! I only need the year of these...
  16. A

    1982 90hp Johnson Lower Unit Oil problem??

    I emptied the lower unit oil since I am replacing the water pump as well. First thing clear water trickled out for a couple seconds and then slightly foamy oil came out and it all finally came out but didn't look very clean. At the fill hole up higher though the oil looked very clean. Is this...
  17. A

    1982 90hp Johnson Water Pump Install

    I am in need of a "visual" install guide on replacing my water pump on my lower unit. I have a service manual but it does not show a picture of how it all should look like together in order. Need to know where all of the o-rings go for the most part. Any links with this info are greatly appreciated.
  18. A

    90hp johnson lower unit

    today i drained the lower unit gear oil in my motor and water trickled out a little bit and then a greenish colored oil came out. It was a little foamy coming out the bottom but at the fill ing hole above it the oil had no water and was clean looking not foamy. Is there a leak somewhere becuase...
  19. A

    90hp johnson

    what is decarbing, I was told to do that after I soak my heads in a mystery oil solution to break it loose. Can someone explain to me what it is and how to do it?? After I get it loose I am going to run it at 24:1 ratio to lubricate everything. Then they told me to decarb it. ??
  20. A

    90hp johnson fuel mixture

    i just got a 1982 90hp johnson and a couple of you answered my question on a soaking to unseaze and now I wanted to ask if anyone has some advice on what type of fuel mixture I should run through it after I soak it and hopefully break it loose. What would be good to get the juices flowing and...
Top