Search results

  1. S

    Stumped

    i have a 1977 200 evinrude i'm trying to get to run good, problem is when its cold the only way to get it to start is to spray pre mixed fuel down the carb throat...and when its warn if you let it sit for 10 minutes or more the same thing happens...what could this be?? i'm getting the correct...
  2. S

    new boat

    i bought this last thursday the trailer is 3 yrs old the previous owner had it built and even gave me the receipt ( $1480 ), the boat itself is 18.5 center console with a blowed 140 Suzuki...i have a 200 evinrude to go on it..let me know your opinions...i gave $1500 for it it needs some wiring...
  3. S

    suzuki parts

    can somebody recommend an online supplier for suzuki outboard parts i need to rebuild a 140,i need pistons,gasket kits,etc.. every website i go to says the catalog isnt avaliable ? i looked on here but i couldnt find 140 parts maybe i'm doing something wrong ? any help is greatly appreciated
  4. S

    1995 Force problem

    A buddy of mine that has a 1995 Force 2 stroke (premix) 40 horsepower motor runs good idling but has a very small miss at WOT just enough to notice, and it only does it every couple of minutes...its getting enough fuel, we went for a boat ride in the river and at WOT i tried to spray some pre...
  5. S

    Baja restoration

    I figured i would start a new thread since the other was so far back and the top cap is already removed, from here on in i'll stick to this thread... After a little work securing wires and dragging a engine hoist to the boat i finally got the top cap removed and it was easier than i thought...
  6. S

    Baja top cap removal

    i'm taking apart a 1975 Baja for a transom and stringer repair, this is my first...i have all the rivets drilled out and all the silicone sliced around the edge where the top cap meets the hull..but something around the splashwell has it stuck good (also have the thru hulls out of the splash...
  7. S

    paint gun

    I bought a HVLP Paint gun from harbor freight (item number 66222) the other day and i just noticed it says "stainless steel needle and tip for use with most water-based finishes" :eek: i'm guessing i bought the wrong gun ?? i was planning on using an oil based paint for my boat what makes...
  8. S

    1977 Baja

    I have a Baja boat i am supposed to get the title saturday ( just bought it not to long ago) i believe it is a 1977 its about 16'-18' i have a hole in the bottom ( about 1/2" wide by 3"-4" long) from previous owners use and i believe the best way to get to it and fix it is to pull the hull off...
  9. S

    shift linkage

    I have a lower unit from a 1976 200 Evinrude and a lower from a 1979 150 johnson will i have to change the shift rods or would they interchange ?? the one from 76 has the screw on collar on the top and the 150 has the curve on the top thanks for any help
  10. S

    200 evinrude

    I have the 200 Evinrude i posted about a few days ago and i decided to pull the heads to see why the compression was low (95 pounds on each cylinder) I found some places on 2 cylinders that looked like a ring or something had bounced around but i am wondering if someone found this and went thru...
  11. S

    200 evinrude

    i diagnosed the problem (with yall's help) on my 1979 200 Evinrude it has a bad power pack i rebuilt the fuel pumps while it is down and i was spinning the motor over to make sure the pumps were ok and the motor backfired :eek: is this normal with a bad power pack ?? i just figured it would spin...
  12. S

    year of motor

    looking at a motor to buy the model number is J150stl any idea what year it is ?? thanks
  13. S

    Stuck Flywheel !!!

    Ok i'm trying to get the flywheel off of a 1979 150 GT...got the nut off no problem but the flywheel on the other hand is a different story...i have a harmonic balancer on it with grade 8 3/8 " bolts after the 5/16 bolts stripped it has had WD40 on it for about 24 hrs now...i tightened the...
  14. S

    200 parts interchange

    Hey guys i have the 1976 200 evinrude with a bad power pack....my question is can i swap all the electronics from a 1979 150 Johnson to the 1976 200 evinrude ?? i have an old parts motor (1979 150) and all the electronics stator,timming base,flywheel and everything are supposed to be good....i...
  15. S

    200 evinrude

    Working on a 1976 200 Evinrude i got for $250 it has good compression #1 95, #2 100, #3 90, #4 95, #5 #90, #6 95....i'll probably do a decarb or pull the head and clean the carbon and get a look inside..the past couple of motors i have built the rod bolts have been stretched pretty bad, granted...
  16. S

    charge for rebuild

    Guys i need your help i built a motor for a guy 1978 140 evinrude , he said do what it takes and as long as he has less in it than a new motor would cost him....pulled the first powerhead and the block was busted so it couldnt be used, didnt find out till it was tore down..(had to fight every...
  17. S

    thermostat housing

    I just finished the rebuild of a 1978 140 evinrude went to start and it fired right up :D but then i noticed the water....it was getting dark on me so really couldnt tell exactly where it was comming from i am suspicious of the thermostat housing though...so i have been researching on here some...
  18. S

    mystery hose

    I am having a memory loss i cant remember where a hose went on my motor i rebuilt...it is a tiny vacuum hose thats connected to the lower part of the intake under the carbs, beside the shift linkage connector...where does the other end go ?? and what does this hose do..i think it goes to the air...
  19. S

    old speed boat find

    Dont know if this is the right place but i wanted to tell everyone about my find i will post pics later...dont exactly know what kind of boat it is but looks like a James Bond speed boat..it came with a 200 evinrude supposed to run but if not i'll rebuild it, 6 life jackets and a bunch of odds...
  20. S

    rejetting needed ??

    i'm rebuilding a 140 (1978) and i'm going .020 over on 3 of the holes the 4th is standard do i need to rejet the carbs ?? thanks Jason
Top