Search results

  1. alldodge

    No start after engine install. Need Help!!!

    All grounds should be well grounded. Don't know if the bracket were the black wire is connected has a good ground or not. The wire might be for a Mercathode which doesn't look like there is one, What we know Voltage is low There is no spark Need to run through the TBV troubleshooting
  2. alldodge

    No start after engine install. Need Help!!!

    Don't know where the wire goes to but black wires should be grounds
  3. alldodge

    No start after engine install. Need Help!!!

    Yes it says there is corrosion and the ignition is not getting enough power Take voltage readings at Bat post
  4. alldodge

    No start after engine install. Need Help!!!

    Looks like you have corrosion and/or weak Bat, At 11.85 it's around 40% charged Fully changed Bat is 12.7V
  5. alldodge

    No start after engine install. Need Help!!!

    Motor has TBV ignition Make sure 12V remains when cranking and if it does Run the TBV troubleshooting
  6. alldodge

    No start after engine install. Need Help!!!

    Something is not connected correctly What is your motor serial number?
  7. alldodge

    4 blade propeller on stringer 400

    Fuel usage is based on HP needed. Fuel usage calculation is between 0.45 to 0.50 pounds of fuel per hour You have a 5.5M (18ft) boat with a 3.0L and boat weight is about 2100 dry. Add fuel gear and people is all variable. Find the prop that with max load you can reach WOT of 4800 rpm and that...
  8. alldodge

    Starter issue

    Grab the belt and try to rotate the motor CCW as your facing the front of motor. Does it move?
  9. alldodge

    Good spray on weed killers.

    I'm using roundup at 2.5 oz per gal and it kills everything Bought 2.5 gal concentrate out of Texas a couple years ago
  10. alldodge

    Audio Warning Alarm weird problem on 2001 4.3 Mercruiser EFI MEFI 3

    To test the alarm, find the engine harness to EFI connector. It's a 4 or 5 pin flat connector on top the motor. Then find the Tan/blue wire and ground it
  11. alldodge

    88150a7 Quicksilver Throttle Issue

    What I would try first is remove the left side cable nut and keeper. Move cable up to left arm not being used and use keeper and nut above. Even if it only fits in the same spot as one on right and see if that gives you 3 inch
  12. alldodge

    outdrive stuck

    Can use a grinder but note steel in bearings is hardened As Lou mentioned heat will help but need a lot of heat fast
  13. alldodge

    Jeanneau prestige 36 2001

    Not sure if info is correct but I'm finding spec is at 0.8 (12 psi), so 0.9 is great and 0.7 is low. Is the 0.7 on the problem motor? If it is then as others have said it's starting to go back to the turbo. The supercharger builds pressure and when the pressure gets to the preset point the...
  14. alldodge

    Jeanneau prestige 36 2001

    Place a gauge on both motors measuring boost. If you see that the troubled motor boost is lower than the good one, it's either a bad turbo or leak in the hoses If boost is good then look at supercharger to see if it's loose and not producing as much
  15. alldodge

    outdrive stuck

    ^^^Agree, water came in from somewhere.
  16. alldodge

    Birds in the boat . . .

    My birds of KY book agrees 12-14 days incubation 12-14 days fledgling and they don't migrate so will be back every year
  17. alldodge

    2004 4.3GXI-E running rich

    Pull the plugs and see if there are any that look real white or black
  18. alldodge

    2004 4.3GXI-E running rich

    Don't think it's the fuel pump right now with info provided. Fuel lines over time can start to degrade and a slight smell can start, but in most cases unless the line is cracking it's of no issue (being your under 2 inch away) This is helpful, I would look at having the injectors cleaned and...
  19. alldodge

    2004 4.3GXI-E running rich

    Need a scanner to watch what the sensors are seeing. Starboard running rich is the one issue, port should draw a steady flow even if it's only 0.1 gph Measure the voltage at the MAP and TPS
  20. alldodge

    outdrive stuck

    Your using the 2x in the wrong direction, lay it horizontal
Top