Search results

  1. MNhunter1

    Free Mercury Tower of Power

    If you don't want it, I'll take it:) I could use the midsection with the newer tilt and trim. Honestly though, if you are mechanically inclined, I'd pick it up. If compression is good, you'd likely be able to get it running or could at least part it out. They might not be highly sought after...
  2. MNhunter1

    New Journey

    Original design, just replaced with Starboard.
  3. MNhunter1

    New Journey

    Gunnels mocked up with some Folbe rod holders, Mate Series cup/rod holders, and Cisco tracks. Still plan to lay down another coat of paint with the Epifanes beads on the gunnel tops, so nothing is attached yet, nor has the trim been put back on. Swapped out the wooden side support/rod holders...
  4. MNhunter1

    New Journey

    Got all the thru hull fittings secured and sealed with 3M5200, bilge pump and float switch mounted, livewell pump installed, and all livewell fittings installed and sealed in the center console as well. After a 7+ day cure, I'll get the Shields 149 hoses cut to length and attached. Will finish...
  5. MNhunter1

    New Journey

    Got my flip/flop seat all finished up. Left the seat cushion unscrewed until I actually mount it in the boat so I can remove it if I need more room to secure it to the deck. This will house the 12 gallon tank and I may try to hinge the seat portion for easier access rather than just screw it in...
  6. MNhunter1

    New Journey

    Still trying to get out and lay down one more doe with my bow, but the hunting season is about wrapped up for the year and I can turn my focus back to the boat. Season was good with numbers, but not so much in the way of trophies. I picked up a new grinder, stuffer, and smoker to start doing...
  7. MNhunter1

    Trailer tongue hinge

    I may be mistaken, but I believe the bolt-on hinge is constructed of a different material than the weld-on, or at least have a zinc finish. I'm no metallurgist, but something to be mindful of.
  8. MNhunter1

    1973 Starcraft SuperSport 16ft. restoration questions

    Yes, you can gang two tanks together, or just swap the fuel line from one tank to the other when the one gets low/empty. Several tanks have fuel gauges, but with the ebb/flow of these boats and the smaller tanks, I always just found it best to judge by the feel of the tank. If it is easily...
  9. MNhunter1

    1973 Starcraft SuperSport 16ft. restoration questions

    I've alw I've always ran portable tanks with any outboard running mixed gas. I just like having the ability to access everything, empty tanks, swap tanks, remove tanks to fill at a local gas station without having to tow the boat there or pay the premium prices at the marinas. A 6 gallon tank...
  10. MNhunter1

    1973 Starcraft SuperSport 16ft. restoration questions

    Mine is a center console, so the holes in the center are for the steering, controls, wires/cables, and livewell plumbing to run under the deck and back to the transom. This model has an aluminum tray that rivets to the stringer to hold all the cables. The livewell plumbing just rests on the...
  11. MNhunter1

    1973 Starcraft SuperSport 16ft. restoration questions

    Yes, drill a hole or two and install the rivet. Only way to ensure everything stays aligned and doesn't shift if you go through and drill them all. I always start with the stringers and do the rib ends last. Put some tape or a stop collar around the bit so you don't drill them too far and hit...
  12. MNhunter1

    New Journey

    I've contemplated this approach as well. Unfortunately, my brackets are not flat on top, so I would need to somehow adjust for that, but still something I am pondering. You can see the little bump where the rod is enclosed, but I could also just grind off the welded on roller arms and use the...
  13. MNhunter1

    1973 Starcraft SuperSport 16ft. restoration questions

    I would strongly suggest forgoing the existing hole locations and just drill new holes. The thought of trying to line up all those existing holes for a tight rivet fit while working with 3M5200 gives me a headache and anxiety. It's much more efficient to drill the new holes and I do not believe...
  14. MNhunter1

    New Journey

    FYI - added a post in the Trailer and Towing thread, tagging here for ease of following/sharing of information: https://forums.iboats.com/threads/bunk-bracket-suggestions.769355/
  15. MNhunter1

    Bunk bracket suggestions

    Yeah, that was a thought too, just lop off the tail that would hang below the cross member. Just wonder if it would compromise the structural integrity as the U bolt wouldn't be completely captured on the lower leg. Also thought I could just drill through the frame and bolt on directly, but...
  16. MNhunter1

    Bunk bracket suggestions

    I'm considering converting my rollers over to bunks. I have a low slung drop axle trailer w/ only 6" of ground clearance. Is there a bunk bracket available that can be mounted on the cross member that will not protrude below the cross member and catch/snag/drag as the lowest point of the...
  17. MNhunter1

    New Journey

    Might be better suited for the trailer/towing forum, but I trust the opinions of the mob a little more than I do the general population. My drop axle/low slung wobble roller trailer fits the boat just perfectly, but I'm tempted to swap out the rollers with bunks. Problem I have is the low...
  18. MNhunter1

    New Journey

    Been a busy week! Nautolex down, hull supports solid riveted in, gunnels attached, hull painted...making progress. First pic of the vinyl was before I glued it down, so may look a little wrinkled. Also could have done a better job sanding some of my hole fills on the gunnels, but they'll still...
  19. MNhunter1

    New Journey

    Photo dump from phone…
  20. MNhunter1

    196X Starcraft Mariner 16

    I would tend to agree. The bow casting deck and existing side console were a PO add on and the side panel structure, supports, and console attachment are all consistent with the SS model. Looks to be a heavily hacked SS.
Top