Search results

  1. M

    Will 1.68 DPSM work for a VP 5.0/5.7 Engine?

    I'm needing a replacement outdrive for my VP 5.7 and I'm curious if this 1.68 ratio will work with my engine properly. It was paired with a VP 7.4 Gi prior.
  2. M

    Kohler 5E Generator shutting off after 3-5 minutes of operation

    Thanks, according to the diagram my issue is not present. When I start the generator it turns on and runs for some time and I am also able to turn it off with the stop switch.
  3. M

    Kohler 5E Generator shutting off after 3-5 minutes of operation

    Now for the relay lights do I need to remove a cover to see the them light up?
  4. M

    Kohler 5E Generator shutting off after 3-5 minutes of operation

    Figured out the issue with why the water was not coming out. It was the coupler behind the water pump itself. Completely disintegrated... Now it's changed out but I still have issues. Now my generator won't even stay on for more than 10-15 seconds the last time it shut down after the 2-3 min...
  5. M

    Radio throwing ground amp code

    I have a Chaparral with a clarion head unit that is throwing an amp ground code. It blasts music loud for a few seconds and shuts off. Where does the ground go for the radio? I don’t have a separate amp it’s built into the radio.
  6. M

    Searay 260 Sundancer Trim Tabs not working!

    Good deal thanks! That should be my issue as I don't have any power or clicking even at the trim tab motor!
  7. M

    Kohler 5E Generator shutting off after 3-5 minutes of operation

    I did not see any LEDs lighted or change. I did not check it. I will have to see which exhaust port it should be shooting water out of. You are talking about a thru hull exhaust port it should be spilling hot water through correct?
  8. M

    Searay 260 Sundancer Trim Tabs not working!

    They are electric over hydraulic. I'm fairly certain they are Bennett trim tabs.
  9. M

    Kohler 5E Generator shutting off after 3-5 minutes of operation

    My generator keeps shutting down on my 260 Sundancer after a few minutes of operation. I've had the carburetor rebuilt and set. My sparkplugs, fuel filter, fuel lines have been flushed and water pump impeller has been changed and the previous one did not have any broken vanes at all. I have...
  10. M

    Searay 260 Sundancer Trim Tabs not working!

    Neither side have any operation. Pressing both of the buttons to lower/raise the trim tabs and there is no audible noise from the motor. Is there just a fuse that typically blows or a relay gone bad?
  11. M

    Sea Ray Kolher 5E Generator Not Getting Fuel

    Fuel line to the carburetor has been disconnected to see if there is fuel pumping when generator is turned over and it sprays fuel. I was able to start the generator and keep it running for 10-15 seconds before I stopped adding starting fluid. Both spark plugs were dry and did not smell like...
  12. M

    Mercruiser Alpha One Gen 2 Leaking Gear Lube from Intake + Not engaging in gear fully after lower shift cable replaced.

    I see, it's not that seal that sits underneath it?
  13. M

    Mercruiser Alpha One Gen 2 Leaking Gear Lube from Intake + Not engaging in gear fully after lower shift cable replaced.

    That’s also another thing I was not clear on. I did not put it in full forward but I did put it 3/4 forward and no locking. Do I need to put in full forward and push push in the cable when it is not attached?
  14. M

    Mercruiser Alpha One Gen 2 Leaking Gear Lube from Intake + Not engaging in gear fully after lower shift cable replaced.

    I attached a diagram, I replaced number 19+21. You are saying seal is number 20?
  15. M

    Mercruiser Alpha One Gen 2 Leaking Gear Lube from Intake + Not engaging in gear fully after lower shift cable replaced.

    I am having an issue with my alpha one gen 2 where I am leaking gear lube from the lower water intake. Another issue is when I go to do the shift cable adjustment as per the manual I cannot get the prop to lock fully when the shifter is in neutral and lower shift cable is pushed in all the way...
  16. M

    Difference between Bravo 3 2.20R vs 2.20 vs 2.21

    Good to know, that is what I will do then. Thanks!
  17. M

    Difference between Bravo 3 2.20R vs 2.20 vs 2.21

    Good deal, exactly what my question was. My drive is solid, corrosion took a toll on the lower unit. Rest of the drive and transom assembly is solid.
  18. M

    Difference between Bravo 3 2.20R vs 2.20 vs 2.21

    I bought a 2.00 Bravo 3X and a 2.00 Bravo 3 as a package, specs showed online that the lowers on the 1.81, 2.00, and 2.20 are the same and I can swap them out. I'm keeping the same upper on mine, I am looking to swap just the lowers. However if I can just swap the complete drive to a 2.00 Bravo...
  19. M

    Volvo Penta 4.3 GL-A Cutting Out After Idling

    All good now! Thanks. I will keep it in mind for the future.
  20. M

    Difference between Bravo 3 2.20R vs 2.20 vs 2.21

    I'm looking to replace a lower unit/complete outdrive on my Searay with a 7.4 MPI that comes stock with a 2.20R. I need to know what difference there is if any between the gear ratios as well as if I can swap just lower units from a 1.81, 2.20, or 2.21 without any issues.
Top