Search results

  1. R

    Melted coil feed wire = Bad Pertronix?

    the error of the resistor wire 1.6 ohms , the resistor wire is 1.8 ohms .
  2. R

    Melted coil feed wire = Bad Pertronix?

    the ignition key is on and the engine is off ,,, around 30sec - 1 minute then the pertronix is the damaged .. also the ignition coil is the purchased it coil ... so you was the pertronix of the wires and then that cap distributor ...you was the cap of the wires of the metal ? I was the plastic...
  3. R

    Mercruiser 3.0 Trouble Starting

    I did the carb top screws .... take it off the carb inspect it . also the float spec position adjusted it .. the throttle cleaner [no carb cleaner ] did the cloth and a very small brush... the gasoline is the alcohol in the carb bowl ... the gasoline is the preventive gasoline marine gasoline...
  4. R

    Melted coil feed wire = Bad Pertronix?

    THE MCM470 engine year 1978 . the pertronix 1146A in the distributor . the resistor wire of the choke 1.6 ohms of the coil positive ...I was doing it over 13 yrs ago... then the engine is a carb of the gasoline and the engine rpm dropping .. the ignition key is turning on the key, the engine...
  5. R

    My 72' gimbal ring has considerable up and down movement.

    the grease was bushing gimbal older years and the worn is the bushing .. the grease is not the cap plastic ..pre alpha 1
  6. R

    Mercruiser shifting problem

    the new shift cable is the fwd drive and the engine top of it the brass barrel center barrel, and the stud 6 inches .... also the cable of the tube turned the cable tighten it up , then ccw 4 turns of that tube ... the alpha 1 ... also the throttle cable is fwd and the prop is the left...
  7. R

    Mercruiser shifting problem

    the alpha 1 outdrive shift cables ... I was the bellows .. then was the wrong shift cable of rev/fwd .. take it out outdrive and inspect it ... the cable shift shaft is in the bellows ... the fwd drive throttle and take it out of the outdrive ..
  8. R

    Exhaust comes out around the bellows, but the bellows appear to be ok...... Whats up w/ that?

    the BRAD888 exhaust bellows is a smaller part ....china ! I did my new bellows of the drive shaft china is a very small part .... then changed it did the old bellows and the new bellows ..! did the company of the Mexico the part is very good ...
  9. R

    Lower unit shaft seal (under raw water pump)

    well the drive outdrive is every year of the air pressure 24hrs in the gear oil ..10PSI air pressure .. the water is the lower outdrive plug and water it ... I did the every year of the air pressure .. the wearing bearings of the drive shaft lower unit !
  10. R

    Exhaust comes out around the bellows, but the bellows appear to be ok...... Whats up w/ that?

    I was the drive shaft bellows ... The china is a smaller Bellows changed it out ... then the company is the bellows SERRIA and the take it out of the old bellows , a small leak of that wear ..then did the SERRIA new bellows did the same part ...
  11. R

    Idles, no power

    did the engine oil ? 40wt , 20w-40wt ...Mercruiser engine oil .
  12. R

    Trim pump hoses replaced

    I was the trim cylinders not working , then the electronic motor pump is no working ..fixed it of those armature brushes .
  13. R

    Trim pump hoses replaced

    I was the trim cyl of the no electrical motor pump ..I was taking it out of the electrical motor .. then did the armature brushes .. then the rusted is the brush holder .. cleaned it did the movement of the brush... then the outdrive up down good .. I did the trim switch of the voltmeter VOM...
  14. R

    Remote sticks when going into reverse, but only when in water.

    the throttle cable of the engine of the top barrel , did the turns 2 turns CW/CCW then the prop is out of the water and the hands are doing the hands of the propeller very strong ..... left fwd /neutral/and the right reverse ... also the outdrive shift shaft is fwd and the barrel center and...
  15. R

    Mercruiser 470 - Cam Seals Repair Questions

    my MCM470 year 1978 is maintenance ... did all of the engine and the boat . wellcraft 20ft ..every year ...the moly grease is the gimbal shaft drive , u joints and the shift shaft cable parts .. I was every year of the gimbal rubber housing inspect it .. then cleaned it . the trim cylinders...
  16. R

    Bad engine coupler or spun prop hub?

    the engine coupler is worn ..
  17. R

    Bad engine coupler or spun prop hub?

    the prop coupler is the company spec part # ? the prop is the company ? and the prop spec ?
  18. R

    Mercruiser 470 - Cam Seals Repair Questions

    SKF STORE 99087 IS NOT WORKING ................ THE FEDERAL MOGUL 99087
  19. R

    Mercruiser 470 - Cam Seals Repair Questions

    yes
  20. R

    Mercruiser 470 - Cam Seals Repair Questions

    Wile cleaning under the oil pan I noticing coolant slowly dripping near the front left of the mounting bracket under the timing cover where the oil pan sits. "Photo 1" showes the coolant drip !!!!!!!!!!!!!!!!!!!!!!!!! MY 470 ENGINE IS THE COOLANT OF THE FLYWHEEL COOLANT WATER PUMP ...
View older results
Top