Search results

  1. ScottinAZ

    MC-1 bellows clamp preferred locations

    Don’t really have a “procedure” I’m following. Yours seems like it will work nicely though. Was mostly seeing where folks aim the hose clamps for access when tightening. Mine were buried at 12 o clock on the joint bellows and 9o’clock behind the water tube for the exhaust. Couldn’t see them...
  2. ScottinAZ

    MC-1 bellows clamp preferred locations

    Ok, normally I would just put the clamps back in the approximate place they were, but that aint happening. Even using the flexible tool to get to the clamps, most of them were located in areas where there isnt even access for that. Is there a preferred clocking on the clamps that while still...
  3. ScottinAZ

    Bellhousing pivot bolt issues....

    Got the buggers...... Autozone had a 1/2 inch allen that is 1/2 inch drive. kept the force much closer to the bolt, and heat did the trick. kept a bit of pressure on the breaker bar, and when the loctite released, they came out easy. Good thing I am doing this job, the bellows were SHOT, same as...
  4. ScottinAZ

    boat and trailer sit very low (to my eye)

    Ok, I think Ill start with flipping the axle. Its cheap, and hopefully the added inch or two will help the ground clearance issue. they like to make the speed bumps HUGE around here, and I dont feel like grounding the trailer on them. if that doesnt help, then a straight axle it is. As for the...
  5. ScottinAZ

    boat and trailer sit very low (to my eye)

    t The bunks need replacement, but the clearance issue is between the frame and the pavement. I only have about 6" between the low point of the trailer and the ground. Bunks will help get the boat higher, but wont stop the trailer from scraping on the small mountains they call speed bumps around...
  6. ScottinAZ

    Bellhousing pivot bolt issues....

    ok, ill get her good and hot with the propane torch after I see if I can procure a 1/2" allen tool here in town. Would prefer to get this off today, rather than have it sit in the yard apart for a week or so waiting on parts/tools..... just wish there was better access to the gimbal housing...
  7. ScottinAZ

    Bellhousing pivot bolt issues....

    Ok, I get that these are a bugger to remove to change the bellows. I had the tool, I reefed on it with a breaker bar, and I stripped the splines on the tool..... new one is on the way... However, before I jack another tool up, or worse strip the spline in the pivot bolt, about how much heat is...
  8. ScottinAZ

    boat and trailer sit very low (to my eye)

    Issue isnt completely with the truck. I can compensate for that..... :D Its just a 1995 F250 4x4, so it does sit pretty tall. However I still think the trailer is too low even just on the jack, with the frame leveled.... here are a few pics. its currently sitting on the jack in the front, with...
  9. ScottinAZ

    boat and trailer sit very low (to my eye)

    ok, boat is just a basic 16 foot fiberglass v-hull runabout. Nothing fancy. Sitting on the trailer I cannot lower the outdrive without burying the skeg, which makes maintenance a pain in the posterior. Trailer came with the boat, and appears to be appropriately sized. Tires are 215/75/14's. axle...
  10. ScottinAZ

    Back after a LONG hiatus....

    Nope. It’s staying as the 2.5 for now. If I was gonna convert it. It would go all the way to a 5.7. Would be massively overpowered, but also a hell of a lot of fun. If I gotta fabricate, let’s go all in!!
  11. ScottinAZ

    Back after a LONG hiatus....

    But where is the fun in that?????
  12. ScottinAZ

    Back after a LONG hiatus....

    Well, Im back in a boat after about a decade now without. Life kicked me hard in the cajones, had to move, sell the boat, move again, and then bought a house and tow vehicle... so naturally, the wife thought the best thing to do would be to buy a boat. Since we didnt learn anything from the...
  13. ScottinAZ

    early end to my season.....:(

    Looks like my season is over for now. Just got word that the roaring noise in the back of the tow vehicle (2002 dakota) is the differential bearings. No tow vehicle, no boating. Enjoy whats left folks, hope to see you on the water next summer
  14. ScottinAZ

    bimini top, adjustment?

    Just got a new bimini put onto my boat to replace the original convertible top that came with it. All I thought was good, but I have an issue with the fabric ballooning up over the frames when going at speed (20-25mph). I know the max speed is 25 mph with the top up, and I was trying to...
  15. ScottinAZ

    Be careful out there this weekend!!

    http://www.azfamily.com/outbound-feeds/yahoo-news/1-killed-3-hurt-in-boating-accident-on-Lake-Pleasant-97750629.html This is why I dont go boating on Holiday weekends, too many morons that dont know what they are doing!!
  16. ScottinAZ

    tell tale fitting thread pitch

    Does anyone know, or can they confirm the thread pitch of the plastic fitting for the tell tale. My '82 115 stopped peeing, and when checking for a plugged line the darn thing broke. (it was a plugged line) I dont mind dropping the buck and a half for a new one, but Ill be darned if I pay 10...
  17. ScottinAZ

    planning a transom job

    Im planning to redo the transom on my 1982 Imperial, and would like advice on what mat and cloth to use on the inside. I will be most likely using locally sourced resin, so that if I run low, I can get more FAST (i have a 2 week limit on the job, due to school vacation). I need advice on...
  18. ScottinAZ

    Allowable "slop" in pistons??

    OK, first off, the engine in question is a 1982 Evinrude 115, (E115TLCNB) that has had an idling issue since purchase. I pulled the plugs, and had evidence of what I thought was water on the plugs, (beaded up liquid on the surface) so I pulled the heads today. Also, I did a compression test on...
  19. ScottinAZ

    fuel pump??

    having some drivability problems with an 82 evinrude 115. At low speeds, after a high speed run, the engine will stall out. Sometimes it fires right off again, and others I need to hit the primer. Occasionally, I need to reprime the ball in order for it to take. Also near the end of the day...
  20. ScottinAZ

    air pressure in pee stream

    Had my '82 evinrude 115 (and the boat it is attached to) on the lake this morning, and was noticing that when the engine is cut off (or more likely stalls, but that is for another post), the pee stream will continue hard for about a second, then there is a burst of air pressure that escapes, and...
Top