Search results

  1. jerryjerry05

    Not permitted

    Not Permitted
  2. jerryjerry05

    2002 225 Mercury EFI

    My 2002 Mercury 225 EFI at idle it runs rough. 1225433ZY XXL SW Almost like there's water in the system(no water, clean/ new filters) After it gets a little past idle it smooth's out and runs really good. Compression is 150# all 6 Thanks,Jerry
  3. jerryjerry05

    Yamaha oil tank system DANGER!!!

    The PROBLEM with Yam's oil tank: the tank should be cleaned out YEARLY!!! There is usually some condensation in the tanks(both) one on the motor and the one in the boat. The condensation forms and settles in the bottom. There it forms an algae that actually grows in oil and diesel fuel. This...
  4. jerryjerry05

    Thermostat part #??

    2002 Mercury 225 EFI ​OT 555086 or 1225433ZY ​I can find the part #s for the thermostat kit that has the thermo's and new covers. ​Don't need the covers. I just need the part # for the thermostat. Seems they don't want you to buy just 1 thermostat and insist you get 2 and covers to go with...
  5. jerryjerry05

    Can anyone give me the breakdown??

    150TXR26G4XSO7891S found on a Yam. Can you tell me what it all means? ​
  6. jerryjerry05

    change from battery CD system with dist to regular auto typ system

    A while back someone posted a bunch of stuff on changing from a Prestolite/mag power to a points ignition system with a coil. ​It showed picks and part on how and what you'd need to change over. ​ANYBODY have a link to this post?? THANKS!!
  7. jerryjerry05

    Some hints on the T@T repairing the relief valve.

    Here are a few pics and descriptions on the T@T relief valve repair You will also need a propane torch and a small pick set.. I managed to get these apart without any other tools Remove the o-rings and keep them. You might need to re-use them. The o-rings don't usually go bad. Once the tools...
  8. jerryjerry05

    Hyd. steering excess play.

    Just repowered with a 2002 225 and used the hyd. steering I had prior. It turns but when setting you can move the motor back and forth about 1-2 inches. All the connections are tight. ​The steering seems to move back and forth in the cyl. ​The motors I had before ere solid and never moved. I...
  9. jerryjerry05

    2002 Mercury EFI

    The top and lower cowl was damaged in shipping.. ​Anybody know where I can get a good used replacement?? OT555086 mod 1225433ZY The difference in a lot is the area where the whizzer tube and water pickup is located. I can work around that. THANKS!!
  10. jerryjerry05

    Speedometer block pressure system.

    This is a "new to me" motor. ​2002 225 EFI OT555086 The speedometer bock pressure system?? What does it do? The hose from the lower to the motor is cut or broken? THANKS!!
  11. jerryjerry05

    ID

    2002 Mercury 3.0 225 EFI ​Looking for the location of the silver plug with the serial #s I looked and looked but no luck?? did find this on a sticker under the cowl.1225433zy ​Thanks, Jerry
  12. jerryjerry05

    2002 Mercury EFI

    I2254332Y T555086 Does this motor have a rev limiter? Where can I get a spec sheet or maybe an owners manual, something that can tell me about the motor?? Thanks.Jerry
  13. jerryjerry05

    Mercury props.

    Just picked up a 2002 225 EFI Came with 2 props. ​The one on it is a Mirage SS 17p ​The spare looks like the standard one. ​SS 17p but shorter and wider blades. I'm guessing that the guy paid a bunch of $$ and was using the Mirage that it's probably the better of the 2?? The cavitation plate...
  14. jerryjerry05

    Cowl upper and lower

    2002 Mercury 225 I225433ZY XL SW 30" I couldn't see a tag or the silver plug(motors on it's side) The upper and lower cowls both need replacing. ​The BIG question is:: will any other years or models swap over? ​The mid section is about the same and from the parts diagrams the bolts might...
  15. jerryjerry05

    Repower. 88 twin 85's to a single 225 Mercury.

    The saltwater finally did enough damage to the mid sections of my twin Forces. They still ran great but I couldn't trust them to go any farther than the inlet and my ocean fishing has suffered. ​I'm repowering to a single 225 EFI Mercury. ​These pics are of the motors after I took them apart...
  16. jerryjerry05

    Transom Mounting holes

    ​ Does the bigger Yamaha's use the same mounting holes as a Mercury? ​I want to mount a 200/ 250 Yam. Thanks, Jerry
  17. jerryjerry05

    1965 9.9

    Got a 65 9.9 in a basket. Luckily it's a fresh water motor and what I had to take apart came easily. The drive shaft was frozen in the crank. Got it out with some help from my hot wrench. Got that apart and now trying to reassemble???? ​The area where the linkage and pull rope is a MYSTERY...
  18. jerryjerry05

    1999 Evinrude E225 FRXEE

    From what I can see the 99 225's were fuel injected?? Thinking about buying?? Pro?? Con?? Thanks,Jerry
  19. jerryjerry05

    Yamaha oil system

    Working on the oil system and need to know how it works????? The tank under the floor has an electric pump and a switch on it (motor) to feed when the tank on the motor when low. Isin't it supposed to feed when the motor runs? What sender sends a signal to the pump to feed the tank on the...
  20. jerryjerry05

    Gill Bracket and motor lenght.

    Thinking about buying a boat with a gill bracket. No motor on it now. ​ ​I know how to measure a normal boat for transom and mounting a motor. ​How do you measure the bracket/ transom to fit a motor on it. Thanks.
Top