Search results

  1. C

    25 HP 4 stroke vs 40 HP 2 stroke???

    A 2 stroke fires every revolution. A 4 stroke fires every other revolution Who has pushed the boat more times and farther in 5 seconds ?
  2. C

    88 Stratos Bass Boat needs new reclear

    Do not do a thing !! Until you find out what type of Clear Coat chemical was used on your boat. Are you sure the clear is original ? Are you as good as a auto body repainting shop ? No dust or insects landing on the wet paint ?
  3. C

    Engine power loss

    A lot of what if's. I have had tanks sent out to be steam cleaned. They had large balls of slime and varnish break loose and stop gasoline flow. The fine screens would allow roll off of the screen mesh and allow limping back to boat ramp. After many limp homes. We drained & used a camera in...
  4. C

    need a new prop ?

    If your cylinders leak in water slowly ??? Older boats. Should be tilted stern downward. left ..right level. With drain plugs out. Or a suction hose used.
  5. C

    Why is finding information on boats so difficult?

    If you are as qualified as Lpgc ? Go for it. Money is needed.
  6. C

    need a new prop ?

    50 hp pushing a 20 in wind and current with 10 people and coolers of food & drinks ?
  7. C

    Why is finding information on boats so difficult?

    Boats are bigger and more difficult to work on parts of the drive train............ Some boat companies BURY common parts. What car company SEALS in fuel tanks ??? Buries engines under bedrooms ?
  8. C

    Engine power loss

    Why would you remove the fine screen in the tank pickup tube ?
  9. C

    Need your opinion about replacing the original Reed Valves in my 1986 Evinrude 30 hp.

    Thank you jimmbo. I just redid the quick putting my palm over the carburetor intake while idling. No more gas droplets on my hand. I still need to add in the Sea Foam. To both fuel tanks. Is there a idle air bleed path in the carburetor ?
  10. C

    Need your opinion about replacing the original Reed Valves in my 1986 Evinrude 30 hp.

    Surprise !! I just remembered a possible cause of idle speed sparkplug fouling reason. I asked the mechanic to RETARD the timing at idle. To prevent the engine from RIPPING the rope and wood handle out of my hand. Had a lawn mower severely bash my hand with a kick back. We did not specify any...
  11. C

    Buy a 5hp Mariner with a blown head gasket?

    You can do a simple gasket repair job. Leave the broken bolts in the cylinder head. If that plate is ONLY holding in EXHAUST pressure or INTAKE pressure ? NOT full combustion pressure ? You can simply use a THIN coating on the area of the 3 holes. NOT a messy coating of each surface !! just...
  12. C

    Bilge pump wiring backwards?

    It is very possible that your water depth is just to low. Happens Fill a large pot of water. Large enough to set the pump level on the bottom. Pull the hose off of the pump. Wires connected to run the pump. It should pump like crazy. It will toss water everywhere (y).
  13. C

    1990 50 hp Johnson reed valves

    Rare but really instantly causes your symptoms............. Watery gas load sold to you that time. Quick test for watery gas is to start at about 1/ 4 to 3/8 of the throttle opening. KEEP HAND on the throttle lever to stop excessive engine speed !!!!! If if starts and runs terrible almost every...
  14. C

    Leak in aluminum boat

    We put on those CHEAP Latex Rubber gloves. Put a tube of outdoor Silicone Rubber inthe caulk gun. WE did the smearing of the caulking on the line of rivet heads on the water sides first. Then did the inside lines last. No reason. Lots of Aluminum boats running decades later............ DO NOT...
  15. C

    Bizarre starter behavior (won't "bench test" on motor)

    You have a open wire or a open squeezed on connector. Or loads of battery post corrosion. Need to use a voltmeter with 1 lead on 1 battery post. The other lead is moved along each wire connection until you get a jump up and dowm place.
  16. C

    Leak in aluminum boat

    Your transom leak is actually the place where the folded over transom is riveted to the floor ? If yes ? Then a person inside the boat with the HEAVY Block of steel is required. And the person under the boat swings a hammer. Less tiring that way. I would use a NON rusting very soft wire wheel...
  17. C

    1990 50 hp Johnson reed valves

    2 bad fuel pumps ? Or is there avacuum in the fuel tank ? Try removing the fill cap on the fuel tank to be sure there is no vacuum. Edit Remove sparkplugs to check if they are NOT perfectly clean. Can you post pictures of the plug ends ?
  18. C

    Need your opinion about replacing the original Reed Valves in my 1986 Evinrude 30 hp.

    For decades I have only used Marine Hi Test with no Ethanol in it. There has been no varnish build up. I also have a fine mesh filter in a glass bowel filter.. I also always run the fuel tanks to completely dry. I am just getting very forgetful about everything.
  19. C

    SAFETY ALERT: Bow Seating Hazard (Malibu)

    Love all the HIGH SPEED people coming out of VERY ROUGH inlets with huge waves. Causing the bow to go under the wave base. That FORCEBLY slams the bow people into doorway and windshield. Or the other person who times the wave. So the bow is suddenly tossed upward. Ejecting the bow people...
  20. C

    Mercruiser 3.0 Alpha One Gen 2 Barrel

    Simply REMOVE the propeller. Then you can use a 55 gallon drum. You have to keep checking the water temperature for getting too hot. Still need at least enough depth in the barrel to cover the inlet holes after the pump FILLS the engine up. You are doing a risky setup.
Top