Search results

  1. C

    Brass block drain plug leaking like a sieve

    Sorry, block drains and plugs are a bit different. Maybe replace both adaptors and plugs. From Flea-Bay: TWO PACK Mercruiser Exhaust Manifold & Engine Block Drain Plug KIT 22-16951Q1
  2. C

    Process for changing boat trailers?

    Take a ride to any marina and see how they block boats up. You may even see a boat similar to yours blocked up.
  3. C

    Brass block drain plug leaking like a sieve

    Std Garboard drain plugs are tapered. You would need a special NPT tap to clean the threads, vs a std bolt tap. The Garboard drain plugs do not normally leak, even when put on dry. If you have the correct plug for the garboard drain, and it leaks, you need to check the garboard drain fitting...
  4. C

    Buy a 5hp Mariner with a blown head gasket?

    You could try marineengine.com, ebasicpower.com or iBoats. Maybe they list another number.
  5. C

    2001 200hp Johnson Float Bowl 0439180

    I did not see any new ones for sale. What is wrong with yours?
  6. C

    VRO delete fuel mix ratio?

    Hesitation to accelerate could be due to a bad fuel pump diaphragm. If the diaphragm leaks, raw fuel can foul a spark plug. If/when the boat gets on plane, the leak can be too small to affect high speed operation.
  7. C

    Replacing my speedometer pickup what sealant to use

    Gee, any sealant that is suitable for below the waterline is fine. I used silicone for 50 years. Pure silicone is completely waterproof. Silicone is also fine for aluminum. Silicone is often used to caulk windows to siding trim made of aluminum. Life Seal is good for wet surfaces. If you...
  8. C

    Process for changing boat trailers?

    All or almost all power boats under 40 feet, may be blocked up in the corners of the transom and under the bow. Drop the tongue, put cement blocks and wood under the transom corners. Lift the tongue and put blocks and wood under the bow. Now you have leave to repair your trailer.
  9. C

    2007 Honda 225 loss of power

    You might check your compression. Did you do that when you first got the motor, as a comparison could be useful. What shape is the prop in?
  10. C

    Process for changing boat trailers?

    Gee, block up the boat and replace the bunks. Pressure treated lumber and a bit of indoor-outdoor carpet and some stainless steel staples.
  11. C

    Buy a 5hp Mariner with a blown head gasket?

    That gasket looks real good. You need to find out why the ones you bought didn't fit. Maybe they sent the wrong ones, or you have a number wrong? You probably want to find out before you need more parts. Maybe you could take them to a Merc dealer and see if they match his stock or something.
  12. C

    Repairing gas sensor / cables / vent gas hose

    Usually when fuel tanks are that rusty/corroded, they are at the end of their lives. Your tank looks to be aluminum. Saltwater + time will rot them out. If it were me, I would pull the tank out, clean it up and see if it is still sound.
  13. C

    How to fix stress crack in fiberglass under seat cushion

    The FG cracked because it was not strong enough. FG cloth provides the most strength of the hull. Epoxy putty like JB weld is strong in compression, but not laterally like cloth is. You can embed cloth in the JBWeld, and add some strength, but not enough, IMO. Grind out the bad glass, and...
  14. C

    Mercontrol shift/throttle lever 75% travel limit now

    Engines usually have a throttle stop setting. This is to protect the carbs from being pushed past their opening stops. Perhaps this adjustment is incorrect on your motor. I am not sure if you have a distributor or not. If so, the adjustment may be above it on a black plate. if 4 coil...
  15. C

    How to fix stress crack in fiberglass under seat cushion

    You need to grind out the cracked glass and reglass it. The best repair would be on both sides, however, it looks like grinding the inside of the cracked glass will be difficult. Can you reinforce the inside with a piece of plywood?
  16. C

    I am starting to believe some of the global warming in N J.

    NJ traditionally had aprox. 2 weeks of real warm weather and 2 weeks really cold weather. We had 4 nice seasons and rain throughout the year. The last 3 years we have little rain during the summer, and more than 2 weeks of hot weather. Real cold weather is gone here as well. I planted a...
  17. C

    Gamefisher 5.0 carburetor

    Sears still has some parts. Your part number may be incorrect. https://www.searspartsdirect.com/model/4bfbp7slmb-000247/craftsman-217585750-boating-parts
  18. C

    I am starting to believe some of the global warming in N J.

    I have lived on the water in NJ for 30+ years. The water level has risen a lot, where I had to raise my dock twice, to keep it above water unless we have a storm. When I first moved into this house in '89, we would have a flood every 5 years or so. Now we have 4 or 5 floods a year.
  19. C

    Just can't start...?? (5hp 4 stroke)

    I worked on a small OB like that, but not sure of brand. It has an internal fuel tank and a fuel shut off valve. To repair it I dumped out the old fuel which was worse than bad, cleaned the carb and added new fuel. I presume your fuel is on and of good quality?
  20. C

    Lubricating a new steering cable

    Older steering cables had zerk fittings for lubricating the motor end of the cable. The problem was that the grease would be forced between the cable end cover and the cable end rod, which could lock it up. Those zerks were eliminated. Steering cables are lubricated and then sealed pretty...
Top