Search results

  1. K

    Gap clearance reed valves? Evinrude 50hp 72 Lark

    Currently inspecting my Lark's reed valves. Manual doesn't give much direction on what kind of gap/clearance is acceptable b/t the reeds and the plate. Basically, from what I've read, you hold them up to a light and if you see a sliver of light coming thru under any of the reeds they need to be...
  2. K

    Mix adjustment screws won't stay in place, considering fix- Evinrude 50hp 72

    The mixture screws on my Lark's carbs won't stay in place after adjusted- threads are not snug enough. As the engine runs and vibrates, they work their way all the way out til they hit the carb cover. They each have a seal/o-ring that might have kept them in place at one time, but they don't...
  3. K

    What does the pressure relief valve in my 50hp 72 evinrude do?

    Just wondering how the pressure valve in my cooling system works, and its purpose. Novice question I know. Thanks
  4. K

    Spring length for Evinrude 50hp 72 pressure release valve spring?

    Just bought a new head for the Lark and when I took the original head off, I was surprised to find that my boat had had no thermostat OR pressure relief valve. Yikes. Anyway, the new head came with both, except for the valve's spring. I ran to Ace today and bought one that fits the valve's...
  5. K

    How does my temp switch work? Evinrude 50hp 72

    Putting on a replacement head and am not sure if my temp switch is trustworthy- looks pretty old. I would like to test it, but would like to know how they work first. My understanding is that there is material inside the switch that changes/lowers resistance as it heats, and when it gets hot...
  6. K

    Thermostat won't close- Evinrude 50hp 72

    Just received a replacement head in the mail which came with a thermostat (the head that was in my engine didn't even have one- is this okay? Is it preferable to maybe not have one and just let it flow? Seems like it wouldn't warm up. Anyway...). I tested the thermo in boiling water and it...
  7. K

    Fuel backflow from engine-side fuel connector- leaking etc. Evinrude '72 50hp

    Hadn't had the fuel line hooked up in a while, decided to crank the engine on today. Hooked up the fuel connector at the engine and when I started pumping the bulb, fuel started leaking from the line at the connector junction. It should be noted that fuel was also flowing into the filter, so it...
  8. K

    Single bolt rusted and not budging on cyl. head- suggestions on how to remove??

    I need to replace the head gasket and rings on my 72 Evinrude 50hp but am unable to get one of the bolts out- seems to be rusted in place or something. Any tips on how to budge a locked bolt?? Thank you
  9. K

    To fin or not to fin? Should I put hydrofoil/doel fins on my 73 Evinrude 50hp??

    Was wondering if there is a great benefit to running with hydrofoils on my outboard. Have a spare pair sitting around but would have to drill mount holes in my boot to make it work (they came with the original lower unit which had holes, the new one doesn't- only difference actually). Is it...
  10. K

    Evinrude 50273c, 50hp '72 no power, swilling fuel

    Have been working to get my engine up and running for a while now and finally thought I had it. Got it back from the shop, they claimed it was working fine under load and was ready to go. Second time at the shop, actually. Took her in the fist time and they got the idle set, new plugs/caps...
  11. K

    Speedometer pitot kit: are all compatible with my speedometer?

    I have a pretty generic speedometer for my boat. Basically setup like this: Custom 80 MPH Black Blue Orange inch Boat Speedometer Gauge | eBay I would like to hook it up but would like to make sure the pitot tube kit I'm looking at will work: Seachoice Teleflex Marine Boat Speedometer Pick Up...
  12. K

    Transom ground (zinc? anode).. should it be wired to something?

    there is a ground near my drain hole in my transom. what is it for? i remember hearing that it has something to do with the gas tank and spark prevention. my tank is all plastic, so maybe grounding's unnecessary. that said, do i need to ground it to anything else? thanks
  13. K

    50hp 72 Evinrude electric shift control wiring question

    opened up my shift selector box and noticed that the green wire was connected under the reverse switch, and the blue under the neutral switch. from my understanding, the blue goes the the reverse solenoid and the green to the neutral. the strange thing is that i've been running with this wiring...
  14. K

    How do I set trim angle on my Evinrude 50hp '72 (specifically, WHAT angle)?

    Not sure to what tilt angle I should be setting my Ev '72 50hp's engine. Have scoured the internet for tips but am coming up short. I have an old 74 Caravelle v-hull that is sized a lot like this...
  15. K

    Oil/gas ratio correct? 72 50hp Evinrude bogging down bad.

    Motor was running very rough- had not had it on the water yet, new used engine. Carbs sparkling and good compression. Took it to shop and they installed new plugs/caps, set the carbs, and did a bit of wiring-- seemed to be running like a top.. out of the water. Next day took her out and when I...
  16. K

    50hp Evinrude 72 only sparking on one cylinder, both coils, rectifier and stator good

    did a spark test on my evinrude 50hp yesterday and only getting spark to top cylinder. switched out coils and they're both good. replaced rectifier, good. removed flywheel and cleaned stator points, still same problem. have a feeling it's the power pack, but would like to run it by the pros...
  17. K

    72 Evinrude 50hp moist air blowing from pee hole with lower unit submerged.

    engine was running hot after i installed new lower unit. this model doesn't have an independent pee hole, so i installed a tap in the coolant jacket as an alternative. cranked her up today and only moist air is coming out, should be a steady stream. don't think this model even has a thermostat...
  18. K

    Intalled new egnition switch on 72 50hp Evinrude- engine runs after switched off.

    thought i had this thing wired up correctly, but guess not. engine keeps running after ignition is keyed off, not sure what's going on. i'm not getting voltage to anything but the start solenoid and the rectifier, which i think is norm, so how would she keep running? suggestions? thank you
  19. K

    Evinrude 50hp seems to be running hot. How do I check water flow to head? No pee hole

    My 1972 50hp seems to run hot after I installed a new lower unit. The pump is fine but I have great difficulty confirming that the water pipe connecting the pump to the head is fitted correctly (tried mirrors and flashlights ect). Very frustrating. I'm fairly sure the pipe's in place, but the...
  20. K

    Evinrude 50273c 1972 50hp drive shaft length?

    Drive shaft is snapped just above the impeller housing- time to replace. I think the Evinrude 50hp 1972 model was made with a long and standard drive shaft length. Before I purchase a new shaft online, I need to know how long the shaft needs to be. Anybody know what the two length are? Thanks
Top