Search results

  1. alldodge

    Alpha 1 Gen 1 Upper/Remote Shift Canle Help

    As you found the amount the cable can be moved unconnected has no direct bearing on how much it will move when connected. The throttle control is the limiting factor
  2. alldodge

    I/O (Sterndrive) Conversion to Outboards

    Merc used superchargers for a short time with smaller blocks and found out there were not reliable.
  3. alldodge

    4.3gxi bad temp sensor?

    Sure sounds like an electrical problem
  4. alldodge

    Name or part # for MC-1 Hook Thing?

    I believe your mixing lift points with hold points The eyelet is there to lift and support the drive to remove and replace. The eyelet is not there to hold the drive up during transport. Using a steel hook to hold the drive up puts much more load on it than that would ever be engineered to do...
  5. alldodge

    Alpha 1 Gen 1 Upper/Remote Shift Canle Help

    The upper shift post can be moved up/down slightly, have you tried to adjust?
  6. alldodge

    Name or part # for MC-1 Hook Thing?

    Best to use something on the trim rams, or tie it up from the cavitation plate That item is the Top cap
  7. alldodge

    Help with OMC 120

    A bad condenser can cause things to heat up
  8. alldodge

    4.3gxi bad temp sensor?

    Anything is possible but both idling shouldn't cause one to die. If electrical connections are bad, maybe Alternator outputs the same when running, should be around 14V+
  9. alldodge

    Help with OMC 120

    You have fuel at the carb so it's not the pump Something is getting hot. Are the points and condenser new?
  10. alldodge

    4.3gxi bad temp sensor?

    Techmate and meter show similar with both motors have me scratching my head again
  11. alldodge

    Help with OMC 120

    ok, pump the throttle does it squirt gas good? If so it's not fuel it's electrical
  12. alldodge

    4.3gxi bad temp sensor?

    The 5v Ref comes from the ECM Now it could be it is at 5v it's just your meter, but if you see 5v on the other motor than that's not the issue
  13. alldodge

    4.3gxi bad temp sensor?

    5v ref is low, wonder if it's a bad connection, bad sensor, or bad ECM
  14. alldodge

    Help with OMC 120

    It ran great for 30 minutes than it started having problems and it keeps getting worst. Could be a sucked up something and clogged up. Could be other things but this is my first thought Does it run better ant higher rpm than lower (below 1800) RPM?
  15. alldodge

    fuel gauge sending unit test

    Not sure if Bobcat uses same as USA standard since Doosan which is South Korea The typical 2 wire sender is one goes to gauge sense post and other goes to ground. Connect to gauge, turn power ON and move float up/down to see if gauge moves. If gauge doesn't move, ground the float sender wire...
  16. alldodge

    Help with OMC 120

    Carb is most likely needs cleaning
  17. alldodge

    Frogs, Lizards and Wasps

    Have wasp, mud dabbers, carpenter bees and Bats no frogs, have lizards Mud dabbers fill every hole 1/4 inch or smaller with mud. Be nice if they would fill carpenter bee holes, but nooo Back shed is riddled with 3/8 holes Developing a wet spot in peak of ceiling, got Bats in the attack...
  18. alldodge

    Prop shaft broken at Cotter pin hole

    Your probably right, my 250HP Verado only uses a lock nut and concave washer to hold prop on, but I also have fine thread
  19. alldodge

    Prop shaft broken at Cotter pin hole

    Self locking nut
  20. alldodge

    Merc 115 4 strokes 2001 ECU/fuel pump problem

    The pump should run full time while the motor is running, the regulator keeps pressure where it should be. I don't know much about a Yam
Top