Search results

  1. dwco5051

    Need advice about a home water well

    There should be a check valve where your well feeds the pressure tank. You would have to tap the hose bib off the house side of the check valve. If you tapped at the well head as soon as you opened the tap the water pressure in the feed from the well would drop to nothing and the pressure...
  2. dwco5051

    Random

    I realized that it was a hypothetical question and said how I would do it if I didn't know the math. However the question stuck in my head all afternoon like an old song while I was out in the woods cutting wood. Even to the point that I was thinking if you used the correct proportions would...
  3. dwco5051

    Random

    Since I am too old to do all that fancy math (it has been over 60 years since I took differential equations and infinite series in college) I would just mix 16 oz of oil in six gallons of gas, mix it up and then scoop out a pint jar of the mix. No exact measuring of quantities to the 3rd place...
  4. dwco5051

    NO POWER

    Can't help with your exact boat but I may b able to help with the basics of most bass boat wiring. You have three wiring circuits. The first is for the motor and would be connected to the main battery. That would start the motor, power the trim, certain gauges such as the tach. The second...
  5. dwco5051

    need help identifying this motor

    That 9.8 Nissan has a dry weight of 81 pounds. Don't know what year and model you old motor was for comparison.
  6. dwco5051

    Important Shop Tip

    If you are shop testing an outboard inside in a 44 gallon garbage can and trying to set the idle in gear do not turn the wheel all the way to make it easier to get at the carb needle. This is especially true if your shop has no floor drains. Wish I had read this in the manual before my prop...
  7. dwco5051

    Fixer Upper

    To get an idea of what you may be getting into here is a pretty complete thread on the restoration of a similar boat. https://forums.iboats.com/threads/76-mfg-fishin-caprice-ii-center-console-rebuild.659167/
  8. dwco5051

    Trailer vin number

    PA F&BC does not handle trailer registrations, only watercraft. Penn DOT has the sole responsibility for trailers.
  9. dwco5051

    Trailer vin number

    Not that easy anymore in Pennsylvania. See; http://www.dot.state.pa.us/public/dvspubsforms/BMV/BMV%20Fact%20Sheets/fs-spconstveh.pdf Many years ago I built a trailer from a set of axles I had from a wrecked trailer and all the rest welded up from scratch. I asked one of my state trooper...
  10. dwco5051

    Switch box

    How many other thing were changed before the box was replaced? Remember the wiring is now thirty years old. Were the plug wires replaced? Model and horsepower of motor along with history of repairs so far would be of help to try and diagnose the problem.
  11. dwco5051

    Minimum MPH Boat/Motor?

    Boat speedometers are not that accurate to even come close to determining your true speed. It is probably going to take some sort of GPS to measure that small of a range. Edit: I use a 30 some year old fish finder with a paddle wheel speed display. It was top line in its day. Now I am going...
  12. dwco5051

    14 ft fishing boat

    Here's mine. 1987 Crestliner Commdore 14' with factory optional side console and live well. Front and rear pedestal seats out and not shown in picture.
  13. dwco5051

    Strange Motor Behaviour.-

    Not to hijack you question but I have a 1987 30a3 right now with a similar problem. Idles well, runs great flat out, but surges back and forth a couple of hundred rpms in between. What I have done so far this Winter. Checked link and sync, it is spot on. Installed a tach so when the ice is out...
  14. dwco5051

    Replace frozen steering cable 1993 Trophy WA

    I feel your pain. I think when they build some boats they start with the steering cable and build the rest of the boat around it.
  15. dwco5051

    Anyone use synthetic nylon winch cable? Or anything besides steel?

    I am guilty as charged. I should have been more specific and not said all nylon. Both my boats are using synthetic straps. I have 4 equipment trailers sitting now at my shop and my tie down straps are all either DOT approved high tensile nylon or poly. Only steel cable is on a recovery...
  16. dwco5051

    Anyone use synthetic nylon winch cable? Or anything besides steel?

    Nylon is just one of the different synthetic materials that are used for rope. It should not be used as a winch line as it has too much stretch. The kinetic energy stored in the nylon rope is equal to force times distance and if the line parts can be dangerous. Be sure if you do change to a...
  17. dwco5051

    Trailering

    If you need more weight on the hitch put a spare tire in the bracket for it on the front. Or even one or two 16" concrete pavers.
  18. dwco5051

    83 Sylvan 18' rewire

    Good page to read before starting before jumping into it. I try to always use the right colors for two reasons. First it will be easier for the next person to trouble shoot the new wiring, second it helps an old guy like me when I forget how I did it...
  19. dwco5051

    Mercury 500 50hp - year unknown, have questions

    The ID tag is located on either side of the swivel bracket (or transom bracket), and the instruction plate is located between the thumb screws above the steering tube. If the tag or plate has been lost or damaged to the point it can no longer be read, there’s a metal plug set in the powerhead...
  20. dwco5051

    Nissan 25hp NS25C3 warning buzzer not operational

    My old eyes read 1990 model, not 98. I am sure that one of the Nissan/Tohatsu wizards on this forum will have the right answer. I wonder if I could add a sensor to my old 1987 model.
View older results
Top