Search results

  1. Texasmark

    tell tale

    Ok how about "consuming" for a word. Also the pump goes from a displacement pump at low speeds to a centrifugal pump (blades bend back....written in engine literature) at high speeds. Displacement pumps have the capacity to suck.....to some extent, depending on the setup and pump.
  2. Texasmark

    Propeller size for 1977 mercury 1150

    You didn't say what length. BW www site (https://www.bostonwhaler.com/boat-models/montauk/170-montauk.html) shows a performance curve with a 115 and 90. I'd think that your 17P with the 2:1 gearbox would work very well. Go fast.com prop slip calculator numbers with the speed as posted on the...
  3. Texasmark

    Short Shaft to long Shaft swap

    ....and drive/shift shaft lengths. I'd think you are looking at replacing 3 parts as mentioned....housing and 2 shafts. Finding a suitable engine with a blown powerhead at a repair shop junk pile might be just the thing for you.
  4. Texasmark

    tell tale

    A couple of idle comments on this unusual (to me) post. How the muffs fit surely affects performance, as does water pressure. With a properly fitting set and adequate pressure the flow should be better since there is no lift requirement....pressure preloads the impeller. Once the engine...
  5. Texasmark

    60's OMC small hub large hub props

    What appears to be in your hand?
  6. Texasmark

    Are press-in rubber hubs still obtainable?

    Back in the '50s for a period, You had Mercury and OMC. Mercury used a splined prop shaft/prop interfacing pressed in, rubber slip hub (had one of those) that would allot the prop to hit an object, break loose from the prop casting proper and upon the operator reducing the RPMs to idle, or...
  7. Texasmark

    Where do you like to prop your boat?

    On where, I prop 2 strokers at the top or a tad above depending on the engine. On 4 stroke pushrod engines I would probably set it in the midrange with the average load carried in the boat. Doing what you suggested will improve you hole shot and get up speed for water toys.
  8. Texasmark

    Are press-in rubber hubs still obtainable?

    Yes they are still available. I bought a new Solace 4 blade, 13+x19 SS just this year.....at a great price.
  9. Texasmark

    60's OMC small hub large hub props

    Yepper that was a fat 50 if a '59 yearmodel. You had to be in an aluminum boat, 12-14', and very young (light weight) in my opinion to even get up with a 9.5...maybe sitting on the pier and getting jerked off to get up.....yes, no????
  10. Texasmark

    60's OMC small hub large hub props

    Your numbers are normal for the prop change you mentioned. Dropping pitch gives better torque (for getting water toys up and going, pushing heavier boats) but reduces speed and increases RPMs usually. OMC went with 4500-5500 RPMs WOT range for many years with the rated HP at 5000. They had...
  11. Texasmark

    Reverse gear and bearing

    I never did it on that engine but the only thing I would do would ensue the shifter is in N or F and you rotate the crankshaft as you push the carrier into position, ensuring that the gears find highs and lows synchronously and not get high centered on 2 peaks....if that's possible...if the tips...
  12. Texasmark

    115 Pro XS Command Thrust on a pontoon - prop?

    Well the Go Fast prop slip calculator says that your 4 blade is yielding a 37% slip and your 3 blade a 19% slip. Large diameter and shallow pitch are the traits of a pusher prop and being shallow in pitch means that RPMs will usually be up which yours are. Per DC Wilsons comment it seems you...
  13. Texasmark

    Prop noise 1200-2000 rpm

    Swag. Your TP probably is ported...holes under the leading edge of the blade designed to allow exhaust gasses to flow across the blades in the hole shot allowing for fast RPM increases and faster HP development which gives you a faster shot. The air/exhaust gas across the blade could allow for...
  14. Texasmark

    What new prop to buy?

    Sorry, thanks for the publicity but I can't help you in that power range.
  15. Texasmark

    A quick way to measure pitch

    Well sir you went to a lot of work and it appears that you have a general purpose low cost aluminum, maybe OEM average performance prop. Any prop that has any pazazz, has multiple angles on the blades, aka a "complex" pitch/rake so attempting to calibrate would be best done by a design...
  16. Texasmark

    Other causes for prop slip?

    My opinion is that 18% slip isn't all that bad if you have a deep V with significant dead rise of the hull at the transom, with an I/O engine, with a lot of weight to be carried....folks, gear and all. If you are carrying a large wake at WOT and best trim you have what I am talking about.
  17. Texasmark

    Whats this hole for???

    With splatter around it I would say it's exhaust relief. When the boat is tied up at the dock or on the trailer in a launching position, the normal exhaust outlet is submerge and offers "back pressure" to the engine which impedes starting. The exhaust relief is a hole in the exhaust channel...
  18. Texasmark

    Found a snake skin in the boat. Now what?

    I'd identify the species if possible. If its not a "pit viper"..triangular head, rattler, moccossin, copper head, or coral snake...small head, black, yellow, orange striped, small body for length I wouldn't worry about it. I know of no instance where these climb above ground spaces...
  19. Texasmark

    Moving from IO to OB experiences?

    You'll get used to it. The rest of the OB experience will be very convincing!
  20. Texasmark

    Transducer

    If through hole type, finding the location from outside the hull will tell you where in the bilge to look for the ducer!
Top