Search results

  1. jerryjerry05

    Which carbs supply which cylinders?

    Nope they redesigned the intake and added a middle cylinder. That motor was said to be the best HP. to Weight of any outboard. The ones I worked on were pretty strong.
  2. jerryjerry05

    1984 Sea King Chrysler

    If the motor was hard starting or there's been a lot of work to get it running?? Then the oily water is normal. The excess gas evaporates the oil doesn't and ends up in the water. The gunk draining down is the result of the above mentioned problems. If your just getting this running after a...
  3. jerryjerry05

    Which carbs supply which cylinders?

    The initial setting is 1 1/2 turn out. Then they get adjusted running at idle in the water, in gear. I thought the top carb fed #1 and #2 The middle carb(little one) fed #3 The bottom fed #4/5?????
  4. jerryjerry05

    120 hp 1995

    Nordin posted it.
  5. jerryjerry05

    2004 150 Yam buzzer going off.

    2004 Yam 150 carb.150TXRD The motor runs GREAT up to 3800-3900 and then the alarm starts. It's NOT overheating, I used a heat gun and checked the temps on each cylinder. Not getting anywhere's near hot. New water pump impeller. The owner replaced both oil sensors/senders in the tanks. Any...
  6. jerryjerry05

    1984 Sea King Chrysler

    Most carb air screws are started at 1 1/2 turns out then adjusted in the water in gear. The idle is about 750-800 in gear motor warm.
  7. jerryjerry05

    1989 Force 15 is this water output enough?

    Like topgun said, deeper in the water. The motor isn't a self priming motor. But once it starts pumping the pump can work in shallower water. Most of the water exits from the snout under the cavitation plate. IF??? your worried??? then change the impeller.
  8. jerryjerry05

    Throttle cable maintenance and adjust basics? Force 85 H.P. or other..

    Sticker= stickeys the first 4-5 post in the Force frum are stickers or stickeys Read them ALL!!!
  9. jerryjerry05

    Throttle cable maintenance and adjust basics? Force 85 H.P. or other..

    The first 4 posts in this forum have tips and procedures for the Force motors. Some of the links don't open but the next one might? U=tube videos by FrankA look them up. Franks was pretty good at his repairs and video's but some of them don't open.
  10. jerryjerry05

    Dont know what model i have

    Ask in the Mercury forum??? This is the Force/Chrysler forum.
  11. jerryjerry05

    Needle valve seats availability?

    Post a close up pic of the needle. The needle/seat: they come two ways. #1 the seat has a tiny o-ring (might be found at Granger)and a solid needle. #2 the seat is solid brass and the needle has a soft rubber tip. Is that seat removable? It doesn't really look like it. Some are pressed in and...
  12. jerryjerry05

    89 force 50 lift ring

    Cheapo tools= crappy results. The 1/4=20 threads already cut into the flywheel, often times they pull out as soon as you apply pressure. Tapping to the next size makes a big difference. One thing I found was using a torch and apply heat direct to the crankshaft end. Then a 3# hammer on the puller.
  13. jerryjerry05

    The saga continues

    Check the trigger leads, they are VERY THIN and break under the shrink wrap, do the tug test and see if the lead pulls out of the connector??? #3 operates the fuel pump, check the diaphragm?? A "New" pack can be bad right out of the box. A stator can test good and still fail.
  14. jerryjerry05

    85 hp force outboard no spark

    85/125 Kill switch's?? They didn't come with a kill switch (KS) on the motor. If it had a KS it usually came on the dash and had a cord and plug. The later years the KS came on the shifter (Mercury) outboardignitiondotcom has some tests for the components they sell. Testing the packs: no set...
  15. jerryjerry05

    97 ish 15 hp force cowl filling with water

    Thanks.
  16. jerryjerry05

    1966 6HP Chrysler Model 6601-02-03 - looking for parts

    Pictures would help? unfortunately you can't add pics until you have 5 posts :( Picture sharing sites will help add pics.
  17. jerryjerry05

    1991 force 150 hp water pump replacement

    WATER PUMP KIT FK1204-1 Most times all you need is an impeller IMPELLER-Water Pump F694065 about 35$ This site sells parts. From the part#...
  18. jerryjerry05

    Tips for Re-Installing a Flywheel?

    A spot of superglue?
  19. jerryjerry05

    Help with 1974 chrysler 1057hf

    Nordin usually answers questions on these older motors? I don't have that much experience on these older Chryslers.
  20. jerryjerry05

    2006 225 4stroke runs poor until warmed up.

    Bosco, none of your business what I do. You don't want to help??? then don't read any of my posts and keep your opinions to yourself. Nothing good to add?? add NOTHING!!
Top