Search results

  1. flashback

    port side exhaust elbow over heating.

    I just finished installing a new elbow, I did find the shutter down in the Y pipe with the help of a shop vac but not the hinge pin. I'll take the exhaust bellows off but don't really expect to find it. No way of knowing how long ago it dislocated so if I don't find it there I'll get on and hope...
  2. flashback

    very cool carb and intake manifold causing moisture

    If the ambient temperature was around 75f and humidity was high it's quite possible you experienced icing. It's common in air cooled engines but can occur in any naturally aspirated motor..
  3. flashback

    Alignment Tool

    Yep, they don't come out of the box lined up.
  4. flashback

    very cool carb and intake manifold causing moisture

    I had a motorcycle that came with a carb heater just for that reason. Your carb is probably icing up.
  5. flashback

    Concerned about Hull Config / Cramped Engine Bay

    Classic case of the sales department and design in bed with each other and the service department in the doghouse...
  6. flashback

    Concerned about Hull Config / Cramped Engine Bay

    LOL every time I as you guys a question like that y'all say pull the motor. And truthfully that is the right answer in a lot of cases..
  7. flashback

    port side exhaust elbow over heating.

    Yep I hear you. Time has snuck up on me as well, this boat has been in fresh water for the last 10 years as far as I know, before that I don't. I'm just gonna do my best to keep it going, when it becomes too much I will let you have it! LOL. and get myself a small one.
  8. flashback

    Can I install a newer outdrive?

    I'm thinking the coupler may not have survived either.
  9. flashback

    Is My Impeller Bad? Mercruiser 228

    A lot of his posts are difficult to understand.
  10. flashback

    port side exhaust elbow over heating.

    Yep between your warning and my curiosity I'm glad I didn't wait until winter. This side had no shutters in it. When I changed bellows in the drive last year I didn't see anything in the exhaust port but didn't really look for anything either. Hard to know what happened in the past, they may...
  11. flashback

    port side exhaust elbow over heating.

    I pulled the starboard elbow today instead of waiting and I'm glad I did. It's worse than the other was.
  12. flashback

    Alignment Tool

    Ok, I thought you were looking for the tool. I don't recall seeing anything on the bearing, but will pass it on if I run into it.
  13. flashback

    Alignment Tool

    The forum has it listed in the stickies..
  14. flashback

    Overheating issue.

    Yes in my limited experience a manifold will hold water unless you pull the drain plug.
  15. flashback

    Figuring out AWG cable size for Dual Battery & wiring?

    Again, it's your choice, I was going for weight balance, It may not affect you, your boat's bigger..LOL ..
  16. flashback

    Figuring out AWG cable size for Dual Battery & wiring?

    I suppose that would depend on the location of the 2nd battery. I put my 2nd battery opposite the 1st battery in the stern so it was a shorter run to the motor than tying to the negative post of the first.. but no reason you can't.
  17. flashback

    glastron fury

    So your saying you have thru hull drains that are under water and no valves on them. I don't even think that's legal.
  18. flashback

    Alignment Tool

    May want to try another caliper for comparison. If you have access to a lathe you could turn it down but you couldn't add to the first stage. That said I think you could still get accurate grease readings.
  19. flashback

    Advice on a 4 winns restoration

    Sometimes they're best left on the wall. That old 50s Chris keeps My heart and mind in agreement.. Best of luck to you,
  20. flashback

    1986 Mercruiser 5.7 Engine Rebuild Crankshaft Questions

    No different as far as I know. Some great engine guys here so just hang tight 🙂
Top