Search results

  1. flyingscott

    1991 Johnson 60 HP not getting spark?

    The control box is where the shifting occurs. Should have a big handle sticking out of it by the steering wheel
  2. flyingscott

    1991 Johnson 60 HP not getting spark?

    Put up a pic of your control box. Anything as new as your motor should have one. Unless it is using an older box.
  3. flyingscott

    1985 Evinrude 25 Starter Wiring

    If you have a push button start here is how your wiring should go. #1 + battery cable to one side of the solenoid on the big terminal. #2 1 wire from push button goes to the + battery cable side of the solenoid #3 Other push button wire goes to 1 of the small terminals on the solenoid #4 other...
  4. flyingscott

    1991 Johnson 60 HP not getting spark?

    Yes got to https://www.outboardbooks.com/ That is a factory manual save your money and do not buy seloc or clymer. One question is the safety lanyard on?
  5. flyingscott

    1985 Evinrude 25 Starter Wiring

    If that is a tiller motor the solenoid is grounded through the neutral safety switch.
  6. flyingscott

    1991 Johnson 60 HP not getting spark?

    Nothing on that strip has anything to do with spark. Have you got a factory manual? Get one if you don't
  7. flyingscott

    1986 Johnson 30 water pump

    Did you put the key in the impeller? Water tube lined up correctly?
  8. flyingscott

    86 Johnson 28 Surging

    What happens if you pump the primer ball? Has the carb been worked on recently? Fuel pump worked on? Put up a pic of the motor and transom. Are you running a shortshaft on a longshaft transom?
  9. flyingscott

    63D orfice high speed jet?

    I agree the jet is not the issue. Can you not message the ebay seller for more info? The size will be stamped on the jet.
  10. flyingscott

    63D orfice high speed jet?

    Ebay has them. seller has 3 left $10.00 simple search to find them. https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2334524.m570.l1313&_nkw=0328544&_sacat=0&LH_TitleDesc=0&_odkw=328544&_osacat=0
  11. flyingscott

    25hp mercury tracker cranks but will not start

    Did you do post #17
  12. flyingscott

    91 Mercury 100 won't run past about 1800 rpm

    Yes if you have the Factory manual you were told to buy
  13. flyingscott

    What year is this Scott outboard?

    1962 14 hp
  14. flyingscott

    96 johnson 20hp temp switch

    I do not believe that has a temp switch or failsafe. I would do a compression test before anything
  15. flyingscott

    First tiller motor

    That hose is not right should be about a 1/4" Id at most. To fix the fuel pump buy the complete carb kit that has the primer also
  16. flyingscott

    2001 Mercury 25hp POWERHEAD

    Rebuild it yourself. The kits and the manual are available. The hard part might be finding a shop that can do a blind Mercosil Bore.
  17. flyingscott

    35 hp johnson one cylinder no compression

    Except for the fact both Fire rings would have to be blown, and one cylinder has compression so Not so sure its a split head gasket.
  18. flyingscott

    Source of Oil Leak

    My bad did not read your comment all the way. Brain fart on my part you are correct
  19. flyingscott

    Source of Oil Leak

    You cannot run out the bottom carbs on that motor ,unless you are above 1800 rpm Make sure the airbox gasket is in good condition and the hose is connected to the crankcase
  20. flyingscott

    1983 evinrude 9.9 2 stroke idle speed setting

    Make sure the snap ring is on tight and the knob is not pushing out. You may need to modify the adjuster I have never seen one that actually worked correctly. leeroysramblings.com has a lot of good info on those.
Top