Search results

  1. Stinnett21

    Vibration TurningPoint 4 blade

    Not doubting you but just to confirm, I think TP props have proprietary hubs right? Do you have their hub? Do you have the aluminum or steel version?
  2. Stinnett21

    New gimbal bearing, can’t get alignment tool in coupler

    It appears to me from the OP's pics those engine mounts have failed.
  3. Stinnett21

    Going to look at the sea doo switch

    Not being negative, it's a neat concept, just wondering how much rattling it would do?
  4. Stinnett21

    Going to look at the sea doo switch

    I thought it was a new product?
  5. Stinnett21

    gear oil drain plug alternative to slotted screw driver?

    External hex would protrude, cause drag and disrupt water flow to prop???
  6. Stinnett21

    gear oil drain plug alternative to slotted screw driver?

    As suggested above a wide screwdriver is the key. I tighten as much as possible by hand then grab the shaft of the screwdriver with small pliers, rock the screwdriver back and forth so I can feel when it's flat against the slot and nudge it a bit tighter. Most of the damage to my slot happened...
  7. Stinnett21

    gear oil drain plug alternative to slotted screw driver?

    I bought the Sierra equivalent for same reason described above (slot getting worn out). Got it all pumped up, removed the pump end, stuck my finger over the hole to stop the bleeding while I grabbed my new Sierra drain plug. Wouldn't go in. Put slight pressure on with screwdriver but no luck...
  8. Stinnett21

    Which gasket is better for impeller install, metal or fiber?

    I'm two impeller changes in (OEM kits) with using the metal gasket with a thin layer of permatex. Have had no issues. I think Merc is combining Verado stuff with Alpha stuff in their kits for marketing reasons. I seem to recall mine containing yellow (rubber I think) orings for drain plugs, I...
  9. Stinnett21

    Fun day!!!

    Love getting out this time of year also. Thank you for your service btw.
  10. Stinnett21

    Tach at 0 when cranking 5.0 MPI

    Had a chance to further investigate. That's my dad's old Fluke from the 80's. It may not be fast enough but if accurate the reading looks ok. Also I swapped batteries and same result so I'm gonna rule out battery as the problem. Something new this time. Tach read 850 rpms a few times while...
  11. Stinnett21

    Tach at 0 when cranking 5.0 MPI

    Good info. Thanks Alldodge. I'll check the connections.
  12. Stinnett21

    Tach at 0 when cranking 5.0 MPI

    This occurred near the end of the day so I don't have much history to go on. I'll observe more on next outing. Good point, thanks.
  13. Stinnett21

    Tach at 0 when cranking 5.0 MPI

    I rarely have a helper but I'll see what I can do. Thanks.
  14. Stinnett21

    Tach at 0 when cranking 5.0 MPI

    It's a two year old Advance Auto 1000 MCA group 24. I realize it still could be bad. I have an older Everstart. I'll swap it out and see what happens when I get the chance. Thanks for the input.
  15. Stinnett21

    Tach at 0 when cranking 5.0 MPI

    I have a 2002 5.0 MPI A1 G2 serial 0M345638. I noticed my tach acting erratic only for a few seconds the other day. First time I've noticed this in 19 seasons and 1490 hours with the boat. After this I noticed the tach went to 0 when cranking. According to other posts on the forum I think it...
  16. Stinnett21

    Prop torque induced list/roll?

    I understand how the trim fin behind the prop can affect steering torque but I do not understand how it would affect boat roll. He has power steering so probably has a flat zinc.
  17. Stinnett21

    Boat Ramp Disaster

    Looks like he didn't have it gear. You can hear it rev but nothing was spinning at least on left side. Also rear brake apparently didn't work.
  18. Stinnett21

    2003 Mercruiser 350 Mag MPI - No start

    The three short double beeps when you turn the ignition off is your stereo head unit reminding you that you haven't ejected the face plate.
  19. Stinnett21

    Bow stop vs bow roller

    I've been through 3 or 4 of the orange poly rollers and eventually they will mark the bow also after repeated sun exposure.
  20. Stinnett21

    Would Smart Tabs help with the pounding?

    I have smart tabs. It seems to me they did help a little with ride but don't expect miracles. An 18 foot boat is getting to be a small boat these days.
Top