Search results

  1. S

    Evinrude 25202r WOT adjustment

    Not ex Not exactly sure on that year but what your describing is the proper way of adjusting the idle/timing which is done at the carb. The adjustment for wide open throttle is done under the flywheel on the port (left) side. There is a long rod with a set screw and that controls how far the...
  2. S

    98 Johnson leaking hydraulic fluid.

    Looks round to me so I don't understand.
  3. S

    98 Johnson leaking hydraulic fluid.

    They make a driver with longer bits at HF.
  4. S

    Remote throttle/shifter + steering for 15HP tiller steer

    Here is a video of how that works and a different one I've never seen.
  5. S

    Remote throttle/shifter + steering for 15HP tiller steer

    https://www.defender.com/product.jsp?id=1054937
  6. S

    Remote throttle/shifter + steering for 15HP tiller steer

    I believe it locks down once you have it adjusted but it's been a long time since I played with one. Had one years ago on a 25 HP Johnson.
  7. S

    Remote throttle/shifter + steering for 15HP tiller steer

    Here is a better picture of the concept.
  8. S

    Remote throttle/shifter + steering for 15HP tiller steer

    Your motor being a tiller model doesn't have a tilt tube for the steering cable to go through. There used to be a model the bolts to the transom and then grabs the motor handle. I see you have the hole at the end of the carting handle. Could find the whole kit but it must be out there. Here is...
  9. S

    1992 Evinrude 150hp EXEN will not run correctly

    Compression test? Did you try pumping the primer ball?
  10. S

    Yamaha F100 TLRY - 2 lower units but only one shaft fits?

    Is the one that goes in a different taper at the top?
  11. S

    Yamaha F100 TLRY - 2 lower units but only one shaft fits?

    Yes, it's not right. You can't beat a SQ peg into a round hole. Have you thought about swapping the shafts?
  12. S

    Yamaha F100 TLRY - 2 lower units but only one shaft fits?

    Not sure on your motor but I have swapped driveshafts in lower units where the top is different but the bottom was the same.
  13. S

    Spark plug recommendations for 1973 evinrude 65 triumph.

    Not really....just something that won't shock you!
  14. S

    Spark plug recommendations for 1973 evinrude 65 triumph.

    The switch would just go between the two connections. This is just for working on it until you get a remote box.
  15. S

    Spark plug recommendations for 1973 evinrude 65 triumph.

    I showed it to you on your red plug. Did you tap on the picture?
  16. S

    Spark plug recommendations for 1973 evinrude 65 triumph.

    Depends on length but 4 gauge should work.....also, no jumper cables aren't marine grade. You need marine grade on a boat or they will corrode very quickly. Marine grade wire is copper that has been tinned silver. It holds up better.
  17. S

    Spark plug recommendations for 1973 evinrude 65 triumph.

    Your starter is still struggling and your partner was playing with the connection. If you don't use all good stuff your going to ruin your starter. Also, don't get ahead of yourself, fix things before you run it.....like the water pump impeller and don't run it without water. Here is the red...
  18. S

    Tilt tube replacement

    0351896 is the part number in stainless.
  19. S

    Broke powerhead bolt

    Well, you did it correctly.
  20. S

    Broke powerhead bolt

    What did you tork the bolts to? If it broke next to the head than when you pull the head off you should have a stub you can grab and spin it out.
Top