Search results

  1. alldodge

    Rule float switch hanging

    My new rule float switch is hanging. Boat had a gas leak on my cool fuel module from a line not put on correctly. After cleaning up the gas an fixing the leak, the float will not move real easy. I would just replace it again but its under the engine and getting to it will be a bi**h. I can...
  2. alldodge

    454/502 knock sensor

    Need to buy another knock sensor. Listing shows 805544T as being superseded by 8M0077616. The issue is the older part is much easier to find and cost a bit less, so guess the question; Is the new one better then the older model?
  3. alldodge

    1970 something Chrysler 105

    Started looking at the Chrysler 105 Conquer boat I pickup for $150 this spring. One of the reasons the guy was selling it cheap is the bottom two cylinders are cracked on the 105. So will need another block or part it out and put something else on it. Looked for the serial number plate inside...
  4. alldodge

    B3 anode connection

    Picked up a prop shaft anode for my Bravo 3 years ago. It came in with a cone nut, hex screw and aluminum anode. Never did install it because after putting the rear prop on I only had 2 to 3 threads left. The new cone nut is not tapered to the degree the original nut is. Looking back the B3...
  5. alldodge

    Transom assembly sealant Yes/No

    Reading through the Merc installation manual it talks about using a locally found sealant around the inside edges to help prevent water absobtion. It does not say to use anything between the transom gasket and the outer hull. When I removed the transom assembly I didn't see anything which...
  6. alldodge

    Transom Bolt hole size

    Need to redrill the holes in my transom, anyone know what size the holes are. My 9/16 bit barely goes in on the two holes I won't be redrilling, but this is also wood. The studs are 7/16 so going to 1/2 would work and could redrill if needed "IF" I can manage to keep the drill in the center
  7. alldodge

    Wetting technic for 1708

    I need someone to tell me exactly how to do the 1708. Don't tell me to wet it and roll it. Give me step by step, please. I just finished grinding all the 1708 and resin back off. I hear wet it first and then put it on. To wet it first will be as I see it a real mess. I don't have much...
  8. alldodge

    Exhaust tips, turndowns and drive shower

    Got my new engine and I have more things to remove and sell and more things to buy, Have a 545HP 509 that needs to have restrictions removed. My silent choice is already removed and Corsa exhaust tip mufflers are getting pulled. So I'm looking for 4 inch thru hull with internal flappers, and...
  9. alldodge

    Bravo III 4 blade vs 3 blade

    The current advertising from Merc is the 4 blade props provide better hole shot and mid range speed. Merc doesn't mention to much about top end, while other forums indicate that top end does suffer. Most of my actual test I have done with any prop with more blades provides more lift but also...
  10. alldodge

    Drill fixture

    In the near future I will need something which will make me drill a near perfect 90 degree holes in my transom. There is the Merc template which cost almost 400, but thinking maybe make a fixture or buy something not so expensive. There are some HF fixtures and others, any recommendations?
  11. alldodge

    Vacuflush sealing

    Tried to remove one of my Vacuflush hoses off the holding tank during the current rebuild. I could not budge the hose so I cut it off. It's on there so tight I wondering if some sort of sealant was used. Looking around I can find plenty of manuals but note state how to install the hoses on...
  12. alldodge

    2 Ton Hoist and Trolley

    Built my first 30x48 pole barn and installed two 30ft H beams with trolley (one front and one rear). Had an engineer at work provide me with the specs to support 3 Tons. Only ever used the front one. Currently building a 40x64 pole barn and want to install either another beam spanning 40 feet...
  13. alldodge

    Dock sank a tad from snow

    We received 6.5 inches and the weight from the snow caused the dock to sink a tad. No biggy the dock should be fine, but did notice the rear of these EZ ports are being lifted. I have two just like these and my Seadoo is still sitting on them. Just a bit of torque being applied to the hinge...
  14. alldodge

    Looking for replacement LED lights

    When I remodeled the great room I installed some 50 watt halogen blubs. Well they are dimmable, put out plenty of light turned almost all the way, but didn't think of it at the time, they also get hot. So hot that in the pick you can see where they are starting to discolor the paint. Need to...
  15. alldodge

    Small Angle Grinder

    Have had many power tools over the years and started buying Dewalts a long time ago after my first using the 18V drill. Since then I have had all kinds and there all still working except D28402 angle grinder. This was one of my newest tools and is around 4 years old. Didn't use it much until...
  16. alldodge

    Got to Love Her

    I love the Admiral but sometimes I see something which makes me stop and shake my head. She saves everything just incase anyone, and I mean anyone needs it. Works for different charity groups to help out the local folks. Loves to shop for bargains and does a heck of a job at it. It's what...
  17. alldodge

    Big block retake on exhaust shutters.

    Removed the old metal pivoting shutters a long time ago on my Formula and replaced them with what I thought was correct. Turns out this was probably in error. Installed 807166A3 which look like these Come to find out through some research I should have installed 807166A1 tpenfield thread...
  18. alldodge

    Westerbeke Gen problem

    Buddy has a 7.2KW Genset and has the issue with low voltage. Currently pulled the capacitor and checked it and it appears good also windings check out OK. In the process of unbolting the Gen so the Gen head can be removed to check diodes. Having real trouble getting the Gen head off due to...
  19. alldodge

    Formula 27PC Transom Work

    Well started with a couple anode holes needing a bit of work and now it appears I'll need to rebuild part of the bottom of the transom. Pulling the transom assembly off noticed all of the bolts had rust but the bottom stud on the starboard side was showing more then the others. When cleaning...
  20. alldodge

    Need a better way to seal up additional anodes

    Had trouble years ago with corrosion on my drive so I installed two additional anodes. The anodes came in a Merc kit and since then corrosion shows very little signs. When I installed, drilled 3/8 hole, passed the wires through, filled with silicone and secured with screws. I am seeing...
Top