Search results

  1. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    Your location ?---For just the bottom half.------Any year Johnson / Evinrude 10 HP from 1958 to 1963.-----Any year 5.5 / 6 HP from 1955 to 1979 model.-----And of course the 9.5 from 64 to 1973 use that skeg.-----I know where to find lots of them.
  2. R

    1989 Evinrude 150xp Temp Gauge, Starboard Temp Switch, Fast Idle & Forward to Neutral Shifting

    ^^^^ Agreed.
  3. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    Hopefully next year I can get out to Alberta again.----Saw the grandson at the----" Canada Wide Science Fair "---- in Ottawa.-----He was a finalist there with his project.----An 8 hr drive for me is easier than 4 days.
  4. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    No it will not.----The skeg from a 56 FD 10 is a bigger unit like the 18 HP.
  5. R

    Toyota/Lexus Timing Belt Change Thoughts

    Most Toyota engines are " clearance " engines.-----Lost the belt on an 84 Supra inline 6.----Put a new one on and it ran like normal again.
  6. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    Johnson marketed a 10 in 49----Evinrude started that in 56 with a 10 HP.-----Not all models were the same between the 2 divisions in the early years.-----Up to 57 the 10 HP used the 18 HP gearcase.
  7. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    Evinrude 10 HP was from 56 to 63 model years.
  8. R

    Johnson TN28 no low-speed fuel

    Rotary valve is just holes drilled in the crankshaft.
  9. R

    50hp Johnson 2 stroke prop

    Try a 21" pitch.
  10. R

    1957 Johnson Rd-19 35hp questions

    Short driveshaft should be easy to find.
  11. R

    Johnson TN28 no low-speed fuel

    Have you adjusted the low speed mixture screw that feeds the rotary valve ?
  12. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    The upper and lower half of the gearcase are machined as a unit .----Considered to be one piece.----You may get lucky just replacing the bottom part.-----Was it cracked due to water freezing ?-----Take it apart to inspect gears and bushing above pinion gear.----This will be costly if you need a...
  13. R

    1964 28hp johnson misfires.

    So run with a timing light.----See which of the 2 separate ignition systems has the issue.----If in fact it is an ignition miss.
  14. R

    1957 Johnson Rd-19 35hp questions

    Do a complete evaluation of this motor before you spend any beer tokens on it !
  15. R

    1957 Johnson Rd-19 35hp questions

    Crankcase compression should build up in a matter of seconds in the tank.-----Perhaps time for a rebuild kit for the tank.
  16. R

    Frankenstein engine build

    Agreed----Notching the crankshaft is NONSENSE !!!-----But sticking some 2 barrel carburetors on the 3 cylinder loopers really wakes them up.
  17. R

    1957 Johnson Rd-19 35hp questions

    The primer button on a 2 hose tank does NOT build up pressure in the tank.
  18. R

    Ignition switch

    Can you post what make / model motor is involved here ???
  19. R

    Gale 5D18B piston rings needed.

    What ring gap do you have ??-----Why do you feel it needs new rings ?
  20. R

    Johnson 4hp lower unit fix

    Propane torch and heat the housing.----Aluminum expands at twice the rate of steel.-----Screws usually come out.
Top