Search results

  1. Scott Danforth

    Electric nightmare

    because in the last 35 years, someone rewired it wrong.
  2. Scott Danforth

    Francine, Kenner, La.

    how are the blender provisions? stay safe
  3. Scott Danforth

    Piston rings for a game fisher 3.0

    As in us a micrometer
  4. Scott Danforth

    How good is your diy aluminum boat paint job

    No, the factory paint was baked on. This is as good as you get without baking, or using imron
  5. Scott Danforth

    Johnson 6hp not pissing

    Basically, use a garbage can and have the water up to the transom clamp
  6. Scott Danforth

    Piston rings for a game fisher 3.0

    It's either a Mac or Tecumseh (eska)
  7. Scott Danforth

    Johnson 6hp not pissing

    Start with the impeller and all maintenance the prior owner didn't do
  8. Scott Danforth

    91 chap restoration

    Ancient Chinese secret. Seriously though my last all fiberglass tub was built around a cut-down sterling storage tub I have also used thin acrylic sheets to make flat fiberglass sheets
  9. Scott Danforth

    Affordable fuel injection intriguing

    mercury used GM ECU's same as the GM crate motors of the 90's and 00's
  10. Scott Danforth

    Lube for Shift/Throttle Cables

    usually they are lubed for life..... when they start to stick, its because they are wearing thru the inner sheath and its metal on metal. that is when they get replaced. normally cables last 15-20 years. yours are 30
  11. Scott Danforth

    4.3 vortec Mercruiser..lots of questions

    that is the part number of the intake manifold. the serial number of the motor will be riveted just above the starter boss or on the top of the spark arrestor (that you appeared to have whited out in the photo)
  12. Scott Danforth

    Mercruiser 3.0 cranks but wont start

    being a 1989, the boat has some age. you may have bad connections between the battery to the motor to the helm. After the quick checks above, start at the battery, and clean every contact until it is shiny additionally, you should still have points ignition. once you get the cranking...
  13. Scott Danforth

    Replacement Fuel Vent Cover

    Looks like an attwood vent. They only sell the whole assembly
  14. Scott Danforth

    Upholstery Decals falling off.

    Did they get a new RF Logo panel made? Or cut the old one off and glue on the new vinyl?
  15. Scott Danforth

    Upholstery Decals falling off.

    the logo should be RF welded, usually by a company such as RF works, etc. as AD stated, some sort of vinyl adhesive. like that found in blow up toy patch kits.
  16. Scott Danforth

    Older Boats

    I have a 14' I use on rivers and small lakes. would never take it out in the ICW or the gulf of mexico. My 19' was about right for a boat for the ICW, however too small in the gulf when there was more than a light chop. My current boat arsenal is the 26 foot for the river, ICW, and the gulf...
  17. Scott Danforth

    Very difficult to shift into Neutral

    yes, that is how it works, however with a load on the cable, the cable can hang up. regarding the carb, just adjust the idle speed. leave the air/fuel adjustment alone. if the cable is pulling against the throttle, that will artificially set your idle different.
  18. Scott Danforth

    Very difficult to shift into Neutral

    at 800-1000 your idle is way too high make sure the shift interrupt switch is working properly. you may need to swap your lower shift cable as they only last about 15 years get your idle down to 600-650 RPM.
  19. Scott Danforth

    Profile 2000 winch bolt removal

    bolt is most likely rusted in place due to the wet strap. try turning the bolt. you may have to cut it off like I did on my old shoreland'r trailer with the profile 2000
  20. Scott Danforth

    What does HEI / D.U.I. replace

    troubleshooting guide in post #4 will identify what the issue is.
Top