Search results

  1. dingbat

    Hvac / thermostat question

    If it was powered you wouldn’t need batteries. ;)
  2. dingbat

    2018 Parker 2810

    Websites lists the length as 28’ with a OAL of 35’ and some change
  3. dingbat

    Can you change from welded to bolted?

    Suggest you find a new coater that knows the process…lol The materials is degreased in a hot alkaline solution then pickled (typically hydrochloric acid) to remove mill scale then dried. From there it’s rinsed then dipped in ammonium chloride that acts like a flux for zinc.
  4. dingbat

    Nobody fishing?

    That’s actually pretty calm for the area. What you’re seeing is the convergence of the Gulf Stream and the Labrador current forming “The Point”, Cape Hatteras, NC You typically need 8 -10 oz to fish the bar but I only needed 6 oz that day to get a decent roll Channel bass (red drum) are the...
  5. dingbat

    Does this LU oil look bad/milky to you?

    They always look "great".......then they leak
  6. dingbat

    Nobody fishing?

    Lots of fishing........not a whole lot of catching. About 20 minutes after this picture was taken I caught three fish on four casts standing in the middle of them and walked back to the truck Some days you have, some you don't.......lol
  7. dingbat

    Does this LU oil look bad/milky to you?

    Yuk......full of water. Did you use new washers on the drains screws? If so, you need to pressure test and replace the leaking seal(s)
  8. dingbat

    Lowrance Elite 12 ti2 issue

    Simrad bought Lowrance forming Navico in 2006. Navico was bought by Brunswick Corp. in 2021
  9. dingbat

    Lowrance Elite 12 ti2 issue

    Lowrance was bought out by Navico/Simrad (Norway) a while ago. At that point the Lowrance brand became the companies "big box" offering. All the hardcore Lowrance guys I know run Simrad equipment
  10. dingbat

    Just thought I'd share a nice photo.

    Few realize how warm the water stays year round . Has a huge effect on our weather
  11. dingbat

    Can you change from welded to bolted?

    I take your looking for a bolt on solution to save a trip to the welding shop. Otherwise it’s an easy remove and replace repair. I was fabricator and certified welder in a prior life but have no idea what shops charge theses days much. The problem you’ll have is finding a support bracket...
  12. dingbat

    2003 Century 32WA with 225 H.P. Would Transom Support 300 H. P. Engines?

    Boat is rated to 500 HP HP is a function of hull design, not weight or strength of transom.
  13. dingbat

    Just thought I'd share a nice photo.

    Nope….Baltimore - Washington DC area. The close proximity to the Atlantic (Gulf Stream) moderates the weather. Not unusual for trees and bushes to bud this time of the year
  14. dingbat

    Transducer

    Found mention of 14 degrees in early model but by 1989 the brochure specs transom deadrise at 17 degrees
  15. dingbat

    Grease on rims

    Can’t install bearing buddies on super lube hubs
  16. dingbat

    Transducer

    Multiple models but only two deadrises, 12 and 20 degrees
  17. dingbat

    Grease on rims

    Next set of numbers up…..1618?
  18. dingbat

    Grease on rims

    Change your rubber caps. I get 2-3 years before they dry rot and start leaking
  19. dingbat

    intermittent tach and not charging 1994 ocean pro 150

    Here is the test procedure to test both the stator and voltage regulator while on the motor. See any signs of epoxy dripping from stator? Don’t run the boat until you get this resolved. Will kill stator sooner than later...
  20. dingbat

    intermittent tach and not charging 1994 ocean pro 150

    Not charging and a cranky tachometer is a sure sign of a bad voltage regulator
Top