Search results

  1. alldodge

    Need thoughts from the car gurus

    Good deal, congrats
  2. alldodge

    2004 Mercruiser 3.0 Aplha One won’t start

    Going from these comments Thanks, S/N list EST Need fuel and spark and you said you have fuel Said no spark Triple check for fuel With mechanical fuel pump might have got the pump arm on the side of the lobe and not centered If there is fuel then Check the connectors on the coil and...
  3. alldodge

    2004 Mercruiser 3.0 Aplha One won’t start

    Being a 2004 (no serial number) I'm assuming EST Dizzy If you didn't actually recheck rotor, do that. If rotor was not installed all the way down the blade would hit one of the cap contacts and break or move it out of position Next check for 12V at the coil (pink or purple wire) with key ON
  4. alldodge

    5.7 Mercruiser Delco distributor Shaft / Housing Exact spacing.

    How did you remove the pin (item 18) from the gear and did you use the correct size roll pin on reassembly? Link is probably not your motor just same Dizzy https://www.mercruiserparts.com/bam/subassembly/31782/1952/40
  5. alldodge

    Went with the Durango R/T

    Nice :D, wish the Admiral wanted one, but no we got another Caddy XT5 :rolleyes:
  6. alldodge

    Dual engine DTS Axius smartcraft schematic

    Maybe @muc can help if he see's this
  7. alldodge

    2000 Mercruiser 5.0 Thunderbolt 5 Ignition idle issue.

    Motor needs more fuel when cold because the fuel doesn't vaporize very well when cold Adjust the choke so it takes longer to open
  8. alldodge

    No compression with rocker arms torqued

    Everything you should need to know and more https://garage.grumpysperformance.com/index.php?threads/big-block-pushrod-guide-plates.4596/
  9. alldodge

    2000 Mercruiser 5.0 Thunderbolt 5 Ignition idle issue.

    This would have helped in first post So after the motor stalls at 0*C can you get it to restart by pumping the throttle? Will the motor keep running once it's warmed up at 0*C? If the above is correct need to adjust your choke
  10. alldodge

    Dual engine DTS Axius smartcraft schematic

    Attached previous is the install manual and it's my understanding that a J box can be attached where the manual shows it can. That said, if it has a 4 port and 6 port can be installed
  11. alldodge

    Dual engine DTS Axius smartcraft schematic

    Not a wiz at this stuff, just understand some of it Replace a junction box with one with more ports (4 to 6) Using nothing but SC stuff is ok/good but might be much easier to use a NEMA 2000 interface and then use a couple Simrad, Garmin or other displays. Can then use the CAN buss to send all...
  12. alldodge

    2000 Regal 2100 LSR 5.0 No start after rebuild.

    See item 35 and it comes as a kit First 35 is for open cooling and Alpha Second 35 is for open cooling and Bravo Third 35 is for closed cooling https://www.mercruiserparts.com/bam/subassembly/31837/2697/10 If you have the old belt, measure it and get one from the gates catalog or local auto...
  13. alldodge

    No compression with rocker arms torqued

    Just a thought swap lifters with one of the other cylinders to see if its stuck lifters
  14. alldodge

    Why am I getting threads on my gmail and on iboats formums

    Why are you getting notifications ??? Normally folks complain about not getting notifications If you set up to receive notifications, then it's good If you don't want to get them then check your settings in profile
  15. alldodge

    No compression with rocker arms torqued

    Suggest, Pull cam and place on blocks then use dial indicator or lobes to verify lift Or could try to measure lift at rocker If lifters where replaced check dimensions in
  16. alldodge

    3.0 L Mercruiser.. HELP!

    Which 3.0???? Been making them a long time, have a serial number?
  17. alldodge

    8.1 GXI-J Cranks but No Start w/ Diacom Logs

    That's a bummer Head bolts usually only break if it was over torqued during assembly, in this case from the factory. Guess there is also manufactures defect with the bolt
  18. alldodge

    Trim Tilt 3 toggle control wiring.

    Look at your wiring diagram top left corner at the trim limit switch. If limit switch is not adjusted right or is not working, only the trailer up switches will work
  19. alldodge

    8.1 GXI-J Cranks but No Start w/ Diacom Logs

    Could be, I always like to put a little oil or grease before installing on O ring
  20. alldodge

    Bayliner Capri 2150 resurrection.

    Nice work good craftsmanship
Top