Search results

  1. R

    Gas line fitting

    Use the correct factory fitting.------Some of this stuff made by the ----" hooflungdung "-----company is just awful.
  2. R

    Chap Quality Control is gone

    Worked at a tire factory many , many years ago.-----Tires were assembled by " piece work " labour.-----Company was investigating building radial tires.-----Bought tires at random from the competitor ( I worked in quality control ) and cut them apart and X-rayed them.-----The company I worked for...
  3. R

    Can I use any 2 stroke oil?

    ???---No the oil does not get into the cooling system.----Once a motor starts to get a little warmer.-----Like your beer glass and condensation.-----The oil disappears ( flashpoint ) and does not stick around the same.----Then the engine friction builds up and it gets worse.-----Some folks say...
  4. R

    Old Mercury Leaking 2-Cycle Oil

    Replace the oil recirculation line from bottom of the block to the upper bearing.
  5. R

    Can I use any 2 stroke oil?

    Well 2 stroke lubrication is not well understood.----Remember that the gasoline vaporizes to be burned and produce POWER.-----The oil ( or much of it ) has to condense and coat the internal parts.---Sort of like the water droplets on a cold glass of beer.---So if the internal engine parts are...
  6. R

    Just bought new boat, trouble first time out. Please help.

    ???----When an outboard like that stops running all the water ( vinegar mix ) will drain out !
  7. R

    1996 Johnson 50. Not starting, backfiring only. Primer issue

    Operating the wee electric primer valve should not change the way the big starter operates.------So I would look at all the wiring.----On the ignition switch.----Inside the control box.----Inside the wiring harness .---Around the motor.----Something is WRONG there.
  8. R

    Milky fluid

    Blown head gasket.-----Or one of the 3 gaskets on the exhaust manifold covers is leaking.
  9. R

    F50 loud clunk

    Well----Check the gear oil for bits of metal.-------Here I would not hesitate to take lower unit apart.-----There may be other opinions.
  10. R

    8HP 2 stroke no start - Low compression

    See post #3----But remember you posted that you have 80 PSI compression.----Motor should bark and roar with 80 PSI in cylinders !!
  11. R

    200 Yamaha 2 stroke head question

    An aluminum plate / piece 1/16" thick to cover that surface.----Put it in place with JB weld.-----Or look into a product called ---lumiweld----An aluminum brazing rod.----Used that stuff myself to do aluminum repair.
  12. R

    200 Yamaha 2 stroke head question

    I think it is another example of poor quality material used in some motors,----Does the hole allow water to exit the block.----Have seen more than 1 example of corrosion like that on that brand of motor !!
  13. R

    8HP 2 stroke no start - Low compression

    It should bark and roar like a raging lion.-----So based on 50+ years of experience I say that spark is weak or non existent.----Or at the wrong time.----Easy to figure out in my opinion.
  14. R

    8HP 2 stroke no start - Low compression

    Put 6 and 1/2 drops of fuel into each sparkplug hole.---Install plugs.----Pull cord 10 times and report what motor does.
  15. R

    8HP 2 stroke no start - Low compression

    Just proof that motors need a new impeller every 5 years or so.-----But check the flywheel key.----A sheared key puts timing way out.----Not a big deal to take the head off for inspection.----The head will be warped and needs refinishing.-----Glass and emery paper does that repair.
  16. R

    Check valve and filter assembly

    Some will argue.----I would remove bypass covers to look at pistons and rings.----Cost you a few $$ for gaskets.----And at 105 PSI on my compression tester the head would come off without hesitation.
  17. R

    1996 Johnson 50. Not starting, backfiring only. Primer issue

    Wire from powerpack to coils correct??----Orange / blue stripe must go to top coil.
  18. R

    Johnson 60ESL70B component

    Tork is 102.5 FT-LBS.----Wasting your time if you do not pull the flywheel off.
  19. R

    Check valve and filter assembly

    Nothing to do with the VRO pump.----Part of the oil recirculation system.-----Post the actual compression values on this engine.----They are world famous for broken piston rings.
  20. R

    Replacing old 2 stroke with newer 4 stroke advice?

    Friend owned a marina and said that he loves the 4 strokes.-----Fork lift fee to take the boat out of the water.---Service work at 100/ hr.----Filters / oil / gear oil / sparkplugs add up to a hefty invoice.-----Well to do folks have no issue with this.
Top