Search results

  1. Scott06

    Marine Power 454 Engines Fuel Pump

    Ok then make sure the pumps are wired through an oil pressure switch if they were added by homer simpson..
  2. Scott06

    Marine Power 454 Engines Fuel Pump

    Those are typical electric pumps set up on carbed engines now. Should be 4-5 psi if working ok. Did u measure fuel pressure off them to carb? Whats the issue you are trying to solve . here is a listing...
  3. Scott06

    Mercathode transom mount 42600A18 on twin I/O systems

    loose the edge, you went swinging Johnson’s as well, and to be blunt i dont care if your drives fall off your boat. when you find your merc instructions you find they don’t really say much… except test the system at the end. But again could care less if your drives rot off.… if you were...
  4. Scott06

    Mercathode transom mount 42600A18 on twin I/O systems

    Forgot the link in my previous post https://www.bottomlinemarine.com/prod_cat/images/8m0148835_is.pdf
  5. Scott06

    Mercathode transom mount 42600A18 on twin I/O systems

    These are what came with my kit. Do you have the transom pucks or the annode under the Gimbal housing. If you have it only under one gimbal housing i would suggest installing it on the other gimbal as well. my friend with a bravo three has two units one on gimbal and one with the transom...
  6. Scott06

    Alpha One Gimbal Ring Hinge Repair?

    Agreed i wouldnt sweat it.
  7. Scott06

    Purpose of spacer on Mercruiser 140, front engine mount,

    The world is t going to end over this but it isolates the bolt from the un numbered horizontal mount casting , otherwise the washers would transmit engine vibration that should be absorbed by the mount #19. Basically you are taking the flexible nature of the mount out of it by tightening it...
  8. Scott06

    TCW-2, use it?

    Yes- my '56 Evinrude 5.5hp says 24: SAE 30 weight , not sure of there was specific 2 stroke back then.
  9. Scott06

    Purchasing 2nd Boat: Jet or Stern Drive?

    One more jet boat detractor- if you like to water ski the wake behind a jet is less smooth in my opinion than a stern drive wake. Also we have a ton of issue with weeds in our jetski so I can imagine a jet boat would be any different. On the ski who cares you are wet anyways but other times when...
  10. Scott06

    Raw water at carb at higher RPM

    So you are filling your crankcase with raw water? i cant see pulling this in from the exhaust, it would fill a cylinder and hydro lock. You would have to have both a leak from raw water side into af side of heat exchanger, and leak from cooling jacket into crank case…
  11. Scott06

    Cleaning Manifolds & Risers

    As long as there is enough meat to mill them down to a good flat sealing surface should be ok. Pic on the right looks like itnhas a chunk out of the sealing surface may require a lot of milling to remove
  12. Scott06

    Ford 289 intake manifold

    I have the same thing on my '65 GTO some of the holes for the carb studs go into the manifold runners. Have absolutely no issue I just put some put some teflon paste , same idea as the perfect seal mentioned . Don't over think it...
  13. Scott06

    Air don't freeze... RV antifreeze DOES!

    This thread is starting to make me look forward to the next oil thread.... Must be winter and were all bored ....
  14. Scott06

    Corrosion on drive

    At this point I'd take the miles and the warranty coverage. Unfortunate but at least some companies still stand behind their products
  15. Scott06

    Cleaning Manifolds & Risers

    before you get too far into it have you scrapped the gaskets off and looked at the mating surfaces? If they are eroded such that you can file flat and get a good seal the corrosion elsewhere is irrelevant
  16. Scott06

    Air don't freeze... RV antifreeze DOES!

    Its is rated for burst protection not staying liquid. All of these will gel, then solidify depending on temp, they just don't expand enough to burst pipes At rated temp.
  17. Scott06

    What should I do with this free boat?

    Best move leave it where u found it
  18. Scott06

    Intake port cc question for 5.7l sbc

    Yeah i would think the smaller volume intake port would better match a stock ish marine build.
  19. Scott06

    Ski Brendella is it worth it?

    I actually thought of buying something similar as an inexpensive ski boat. If for personal use yes. If you think you are going to flip it and get paid probably not. The upholstery if you have to pay for it is a killer. The carpet in the first pic looks newer it may have been re-decked and...
  20. Scott06

    Corrosion on drive

    Definitely more of a corrosion risk with dual SS props. Anybody who has a Bravo III has likely experienced this, but VP DP drives seem to fair better. Even on my alpha one gen two, since switching to a big SS Revolution four prop I get more corrosion and anode wear than with a smaller SS...
Top