Search results

  1. Scott Danforth

    Volvo Penta SX whine developed

    Check drive lube
  2. Scott Danforth

    Lifting Motor. Build Stand-Alone Gantry or Will This Work?

    I gav removed the tires completely and ran the trailer on the hubs if you need more clearance
  3. Scott Danforth

    5.0 GXI Swap Heads & Cams Or No?

    Could be cad plating. Check with a magnet
  4. Scott Danforth

    Where to run anchor line?

    Cleats on all 4 corners. Keep rode in a milk crate under the helm. That way, it's out of way until you need it
  5. Scott Danforth

    What kind of paint to use for longevity

    6" DA with 80 grit
  6. Scott Danforth

    4.3 GL tune up spec questions

    Under the squirter is a needle that acts as a check valve. This sometimes gets gooed up. Normally you only need the bowl gasket and the metering block gasket. Idle circuit pulls from bottom of bowl and thru bottom of metering block. Accelerator pump either has a check ball (older) or a...
  7. Scott Danforth

    4.3 GL tune up spec questions

    Paint is Ford red if you need to paint it
  8. Scott Danforth

    4.3 GL tune up spec questions

    4.5 power valve
  9. Scott Danforth

    4.3 GL tune up spec questions

    Nevermind. 75006 = 80316 = 500 cfm
  10. Scott Danforth

    4.3 GL tune up spec questions

    What is the air horn numbers?
  11. Scott Danforth

    4.3 GL tune up spec questions

    Scott, I can walk you thru if you need. Does this have externally adjustable float? (Hex nut and screw). If so, super easy to set float. A 2300 2-barrel will be a 350 CFM or a 500 CFM. Only other changes are slight jet changes. Other than that, nearly all 2300's are similar
  12. Scott Danforth

    4.3 GL tune up spec questions

    Holley carbs are easier than anything else to rebuild. Make sure passages are clear
  13. Scott Danforth

    4.3 GL tune up spec questions

    Take the air horn numbers and look here. https://www.google.com/url?sa=t&source=web&rct=j&opi=89978449&url=https://documents.holley.com/techlibrary_carb_numerical_listing.pdf&ved=2ahUKEwibjqCNlYWAAxXHnWoFHX0QA_YQFnoECBkQAQ&usg=AOvVaw1UziVPwG2-N82hs9EiLZMZ
  14. Scott Danforth

    Lifting Motor. Build Stand-Alone Gantry or Will This Work?

    I would do 2x10's across the top. 2x6's vertical and a couple of 2x4 k braces
  15. Scott Danforth

    Impeller replacement question

    Lube impeller with either a drop of dish detergent or a drop or two of water soluble glycerin such as KY jelly If your in the water, the pump is below the waterline, so it will self prime
  16. Scott Danforth

    Reeds Cub Scow modifications

    I would sell it as-is and negotiate
  17. Scott Danforth

    Trouble coming on plane

    So drop down to F3s
  18. Scott Danforth

    Mercruiser 3.0 LX wont start after turning engine off. Video

    Check the block ground
  19. Scott Danforth

    1978 Chris craft 281

    Ask questions in the open forums
  20. Scott Danforth

    Volvo Outdrive I.D.

    The hose is flared on the end and held in by the power steering cooler Suggest getting a manual
Top